How to prepare PEG thin film using PEG 3300?

04 April 2018 0 6K Report

I am using PEG 3300 (don`'t know about MW may be 3300 is MW not sure).By dissolving PEG in ethanol .spin coating it .

Badges
Science topic

More Abhishek Thakur's questions See All

Can we synthesize thin films of poly acetylene using powder poly-acetylene as a precursor?

Lot of polymers are commercially available in solid form, which can be dissolved in some solvent to make a solution. By , evaporating the excess solvent one can easily synthesize thin films of...

05 June 2019 1,607 7 View

Is it advisable/correct to measure polymer crystallite size using conventional methods?

For calculating using x-ray diffraction, SAXS is a good approach but , few people reports the calculation using XRD at higher angles also. Is it correct to use Scherrer's formula or willamson...

05 June 2019 8,165 3 View

Why polypyrrole is conducting not semiconducting ?

Synthesis and Characterization of Conductive Polypyrrole: Th...It shows a graph of Temp. Vs res. which is clearly shows a semiconducting behavior i.e resistance increases with decreases in temp....

04 May 2019 4,957 4 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

For the moringa oleifera extract using ethanol as the solvent,what is the alternative method to concentrate the extract other than rotary evaporation?

99% pure ethanol was used for maceration also alternate methods along with the temperature and time to concentrate the extract can be specified

31 July 2024 5,113 4 View

Is there a good freeware software for photodocumentation of TLC?

I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?

31 July 2024 8,415 1 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View