Please elaborate the process.
Dear Dr. Sharma
I think you should use E-SEM for imaging this sample. If you have not access to this equipment, its better to freeze-dry your sample and then make a thin layer (
I have made paper out of cellulose (by filter drying it).Can I coat Gold over it and obtain good SEM images?
Does scan rate has any impact? what other parameters to consider while performing xrd ?
08 September 2018 6,936 2 View
I have standard data of Silicon sample and I want to subtract instrumental error (FWHM) from my sample. My sample and Silicon diffractogram are having peaks at different 2theta values (obvious). I...
07 August 2018 6,060 9 View
YAG is Yttrium Aluminium Garnet.
07 August 2018 4,787 8 View
Can I perform test directly using the paper sample? If I need a solvent to perform test which could be suitable solvent?
07 August 2018 10,071 2 View
I am comparing crystallite size and strain using Scherrer and Williamson hall method.But I have doubt in mind whether the value of FWHM I am using is correct. The Bragg peak width is a...
05 June 2018 7,717 13 View
please give papers/ references, if possible.
05 June 2018 4,373 4 View
Please share the data if you have.
05 June 2018 6,679 2 View
I performed Willamson hall analysis of 4 smaples of YAG nanoparticles . I included top 9 peaks (same) in each case to get a linear fit line.However, in two samples adj R square value is positive...
05 June 2018 4,560 2 View
my xrd resembles Cellulose 2 structure OBTAINED FROM BAGASSE. Is there any other easy method to calculate crystalinity ?
05 June 2018 619 0 View
here are the results (O -Oxygen, Al Aluminium ,Y- Yttrium)
04 May 2018 4,056 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View