Whether to plan experiment based on methinine & lysine content of all roughage and concentrate and per cent composition of growth tissue or other siutable methods
I will refer for Do my Mpharm project on Targeted Drug delivery for the treatment of Breast cancer.Please tell tell your Suggestion,Opinion,Idea about Possibility ,merits and demerits. Please...
05 December 2020 5,582 4 View
I have submitted one of my review article on COVID 19 and ophthalmology in April through online submission but journal haven't overlooked it inspite of several request. Even i have sent request...
06 August 2020 1,802 3 View
How trapped water inside the RGO sheets helps to enhance the specific capacitance of energy storage material?
02 January 2019 7,308 4 View
I had done PCR with cDNA and got some non specific band. Now i have very limited cDNA, which is not enough to perform all PCR, So can i use my previous PCR product as DNA. I have attached my Gel...
06 September 2018 8,721 7 View
I tried to find GAPDH from mice brain after anesthesia, Using Kit, I find RNA and then cDNA. However, I get the band but the thickness is not like that what I desired. So what to do to get a thick...
13 August 2018 9,501 5 View
What is the reason that when we minimize the dc gain of the asymptotically stable LTI system, the poles of the system is shifted in left-hand side or the transient response of the system is...
06 February 2018 4,396 3 View
if, i am getting specific capacitance 151 F/g at 1 A/g in GCD then what will be the appropriate scan rate in CV to get same specific capacitance at potential window 0.9 V for both? How EIS depends...
10 December 2017 8,677 5 View
Hello there! I have three parts in my model: a heat source (a circular coil with a hole in the center), a plate and a an air domain which are merged as a single part. I have carried out an...
09 May 2017 7,509 3 View
I am working on the NVP cathode material for sodium ion batteries. I want to take ICP of that material to get information on chemical composition. I don't know which solvent is suitable for that.
09 February 2017 3,996 2 View
29 November 2016 8,145 2 View
Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !
01 March 2021 2,501 3 View
28 February 2021 9,936 2 View
We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...
25 February 2021 568 1 View
I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...
23 February 2021 6,043 1 View
I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...
22 February 2021 4,290 1 View
does anyone know the best method to differentiate and quantify rapid fatiguing and fatigue resistant muscle fibers? the old method form the 1980's uses ATP staining which is quite labor intense?
21 February 2021 6,483 3 View
Hi guys, I am facing problems to interpret a DMA results. Material: Composite Bisphenol A + curaua fiber What is being tested: the influence of fiber volume on the composites properties...
12 February 2021 174 7 View
What is the reason of the received optical signal to be slimmed down in multi-mode fiber? I have 4 km multi-mode fiber
03 February 2021 1,105 10 View
I am modeling Carbon Fiber Reinforced polymer wrapped concrete column in Abaqus, but I have faced so many difficulties especially in the Model< Interaction and Constraint module. SO could you...
26 January 2021 6,795 4 View
Electrospining method is important for production of nanofiber .If doped with nanoparticles ,can be used for remove of contaminant such as VOC , but don't have mechanical strengh . For finding a...
24 January 2021 7,290 3 View