How to perform impact analysis in ABAQUS?

12 December 2015 1 3K Report

The FEA analysis for abrasive flow machining to be perform in ABAQUS for validating the impact effect of abrasives with experimental work.Which kind of material models are preferred for simulation work.

Frank Richter

ABAQUS mailing list

https://groups.yahoo.com/group/ABAQUS

Badges
Science topic

More A. Tamilarasan's questions See All

What are the scope for Paid SCI journal?

Some reputed publishers having the journals in SCI indexed journal.. But while punishing the papers the author to pay publishing fee after acceptance...What is the use and scope of the published...

08 September 2018 5,326 0 View

How to prepare nano particle based metal matrix composite?

Pls suggest the route and procedure to prepare nano particle based MMC..

08 September 2018 2,966 6 View

What are the important statistical measures for quantifying the multilevel thresholding of image segmentation while using four algorithms?

I want know the various statistical metrics to confirm the more suitability of one algorithm as compared with other algorithms.

07 August 2018 865 6 View

Difference between histogram and normalised histogram in image segmentation?

While looking many papers, I have found y-Axis in '0 - 3000' range of number of pixels, that is very easy to understand. But, some others specified that '0- 1.2' range. Certainly i confused...

04 May 2018 8,133 2 View

What is the state of art research in transformer oil?

Advances in transformer oil yielding high transformer life.

31 December 2017 3,316 3 View

How do understand image segmentation basics? And, a sample manual calculation need for any image?

A sample of image segmentation manual calculation is required.

31 December 2017 6,529 5 View

How will do the manual calculation of image segmentation on 2D image?

In a gray scale image, how to segment the image manually using hand calculations

11 December 2017 6,017 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View