How to perform both heat and mass transfer analysis of aircraft engine in ANSYS FLUENT?

More Faraz Ahmad's questions See All

Protein-aptamer gel electrophoresis help, please??

Hi, I have problems with running gel electrophoresis. I have tried agarose gel electrophoresis and native PAGE. I have two proteins, which have molecular weights of ~30kDa and ~180kDa and two...

03 March 2021 4,275 4 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Expression cloning by using cDNA,do I need to modify the cDNA first?

I am going to have a expression cloning of mammalian gene by using shuttle plasmid to transforming the E.coli However I don't know I should only inserting the Coding sequence ,or I can...

28 February 2021 5,440 3 View

I need dataset for recommandation system?

Hi every body I need to collect datasets from different source to work on recommendation system algorithms, could you advise me how collect data?

27 February 2021 7,063 7 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Why tick's salivary gland extract didn't run in the gel (SDS PAGE )??

Greetings, I want to make SDS PAGE for my sample (Tick salivery gland extract), I tried concentrations 10%, 12%. I also tried high molecular weight ladder. But the protein stopped at the top and...

25 February 2021 7,698 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

How to estimate 2SLS with different instruments for different endogenous variables?

To be specific, I want to conduct an IV regression in stata with the following three equations. EQ1: Y1 ~Y2 Y3 X EQ2: Y2 ~ Z1 EQ3: Y3 ~ Z2 Both Y2 and Y3 are endogenous. However, Z1 and Z2 are...

23 February 2021 6,266 3 View

Which microtomy technique do you suggest for thin and delicate root sectioning ?And, how to preserve and process the roots before sectioning?

We have thin roots of from 1 year old different species of plants. We are looking into anatomical details of the roots. What's the best method to preserve and process the roots once they are...

23 February 2021 1,898 1 View

How to find out the problem of VMD software when i run it?

Hello I try to install and run the VMD software on windows 10 (64-bit).It doesn`t work and it is closed when I run it. I checked all of tutorials, videos and documents. But they did not work...

22 February 2021 8,211 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Trouble with Charting with Google Earth Engine (Technical)?

Hello. I have a problem with the charting in google earth engine. I created an image collection by combining 5 image collections of five parameters and using ee.Join.inner ( ) and .apply ( )...

26 February 2021 7,084 2 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

Olexiy Shynkarenko

The question is very general, it's very hard to advice something. More details are required to give a complete answer. Try to see Ansys Verification Models tutorial. Examples of coupled models are described there.

Naas Toufik Tayeb

about mass transfer, you can use multiphase models if FLUENT software like:

- VOF

- Species Transport

- eulerian

- mixture model.