How to overcome the error in Ansys "Deformation is too large compared to bounding box dimensions" ?

02 February 2017 0 5K Report

When I am in need to define displacement for the object the bounding box being constraint for me ? So What shall I do ?

Badges
Science topic

More Karthick Munisamy's questions See All

What kind of colloidal solutions can be used in heat storage applcation ?

In colloidal solutions, liquid/solid particles are dispersed in other solid/liquid . Among that what kind of colloidal solution can be used in heat transfer application

31 December 2016 3,339 2 View

How to use imprint faces option in design modeller (Ansys-Workbench) to model a moving heat source ?

I need to model a Gaussian Heat Source that moves over a plate with a constant velocity/ constant heat flux using Workbench

31 December 2016 8,728 3 View

What tool should be used to model a moving heat source in Ansys ?

In Ansys Workbench , Fluent, CFX, Static-structural & thermal, Transient -structural & thermal, etc are available. Which is better to use and how ?

31 December 2016 2,641 4 View

I need to define velocity of an object in Ansys, but bounding box dimensions become limitatation, what to do ?

I need to move object by displacement option in Ansys solver but the dimension of bounding box of the object remains constraint for the process, is there any other method to do it ?

31 December 2016 8,073 1 View

How to analyze welded joints in Ansys ?

When two metal plates to be welded, with a moving heat source (Gaussian) with a constant velocity

10 November 2016 1,632 3 View

In Ansys Fluent , how to analyze the quantity of distilled water produced in the solar still ?

I have done analysis in Ansys Fluent for the temperature distribution only, but not for the yield of the still. Any of you please give me some useful suggestions

10 November 2016 449 3 View

How to set boundary conditions for solar stills in Fluent ?

Solar still absorbs radiation to evaporate water, so it involves muti-phase. What are the boundary condition when solar still basin (metal) insulated(wood) and top surface is closed with glazing...

10 November 2016 4,649 5 View

How to perform TIG welding , with a moving heat source Analysis in Ansys Workbench ?

I know to use Ansys Fluent only. Is that possible to perform the above analysis in Fluent or should I go for CFX/Multi-physics/Transient-thermal

10 November 2016 1,643 1 View

How to calculate the cost of distilled water produced per litre and payback period of solar still ?

Type of solar still Cost of solarstill ($)Average yield(kg/m2)Cost of freshwater/litreCost of waterproduced/day ($/day)Payback period = (Investment/costof fresh water /day) in daysConventional...

07 August 2016 4,600 2 View

Is there any possibility of using oil as a sensible heat storage ?

Oil are relatively cheaper compared to other energy storage material. If Oil is used as Sensible heat storage what is the maximum heat that can be stored in the oil ? What is the useful life of...

01 January 1970 9,478 16 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View