How to use imprint faces option in design modeller (Ansys-Workbench) to model a moving heat source ?

More Karthick Munisamy's questions See All

How to overcome the error in Ansys "Deformation is too large compared to bounding box dimensions" ?

When I am in need to define displacement for the object the bounding box being constraint for me ? So What shall I do ?

01 February 2017 5,115 0 View

What kind of colloidal solutions can be used in heat storage applcation ?

In colloidal solutions, liquid/solid particles are dispersed in other solid/liquid . Among that what kind of colloidal solution can be used in heat transfer application

31 December 2016 3,478 2 View

I need to define velocity of an object in Ansys, but bounding box dimensions become limitatation, what to do ?

I need to move object by displacement option in Ansys solver but the dimension of bounding box of the object remains constraint for the process, is there any other method to do it ?

31 December 2016 8,199 1 View

What tool should be used to model a moving heat source in Ansys ?

In Ansys Workbench , Fluent, CFX, Static-structural & thermal, Transient -structural & thermal, etc are available. Which is better to use and how ?

31 December 2016 2,782 4 View

How to analyze welded joints in Ansys ?

When two metal plates to be welded, with a moving heat source (Gaussian) with a constant velocity

10 November 2016 1,787 3 View

In Ansys Fluent , how to analyze the quantity of distilled water produced in the solar still ?

I have done analysis in Ansys Fluent for the temperature distribution only, but not for the yield of the still. Any of you please give me some useful suggestions

10 November 2016 610 3 View

How to set boundary conditions for solar stills in Fluent ?

Solar still absorbs radiation to evaporate water, so it involves muti-phase. What are the boundary condition when solar still basin (metal) insulated(wood) and top surface is closed with glazing...

10 November 2016 4,823 5 View

How to perform TIG welding , with a moving heat source Analysis in Ansys Workbench ?

I know to use Ansys Fluent only. Is that possible to perform the above analysis in Fluent or should I go for CFX/Multi-physics/Transient-thermal

10 November 2016 1,804 1 View

How to calculate the cost of distilled water produced per litre and payback period of solar still ?

Type of solar still Cost of solarstill ($)Average yield(kg/m2)Cost of freshwater/litreCost of waterproduced/day ($/day)Payback period = (Investment/costof fresh water /day) in daysConventional...

07 August 2016 4,850 2 View

Is there any alternate Phase Change Material for Paraffin ?

Paraffin has good thermal stability , heat storage capacity, also does not react with metals by means of chemical reaction and cost effective. Is there any alternate for this material ?

01 January 1970 3,421 9 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View

Sathish Dhandapani

http://docplayer.net/9906959-Tips-and-tricks-design-modeler-ansys-meshing.html

Arnaud Contet

For software specific questions, you should really ask the company's tech support.

Hamidreza Ahmadi Moghaddam

Interesting question. Since the heat source is changing in respect with time , scripting can be a good solution for changing the boundary condition over the course of the analysis.