How to model brazing/difusion bonding using ansys?

Chitaranjan Pany @Chitaranjan_Pany

03 March 2018 0 6K Report

The component consists of alumina copper and alumimum alloy are to be brazed or diffusion bonded.

Badges
Science topic

More Chitaranjan Pany's questions See All

What are properties such as young's modulus, poisson ratio, comppressive strength of asbestos ?

for usage as gasket purpose subjected to high temp and pressure.

01 February 2019 1,528 2 View

How resonance survey related to random vibration?

random vibration analysis.

09 October 2018 7,920 0 View

How to model diffusion bonding of impeller vane by FEA ?

literature, FE modelling / analysis, failure

08 September 2018 4,413 1 View

How to find stiffness,mass matrices from an Ansys FE model?

Extraction of stiffness, mass and geometric stiffness matrices from an Ansys model.

02 March 2018 5,665 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

Can Langmuir constant related to bonding energy (Kl) and Freundlich exponent (1/n) indicative of ads intensity show opposite trends with temperature?

The adsorbate is Arsenic and the adsorbent is a soil

18 July 2024 332 8 View

How to create parameter and coordinate files for ligand in amber when FATAL error (maybe due to duplicate bond specifications) happens?

Hello, I'm trying to create parameter and coordinate files for a drug (PRG-A01) found on the following page: http://www.probechem.com/products_PRG-A01.html I used the guide made by Michael...

17 July 2024 3,472 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View