Can anyone send me article talking about CFX code and relation with thermal fluid?

04 May 2017 8,494 0 View

Can I submitted in thermal energy?

04 May 2017 8,475 2 View

Who can show me the calculus of heat transfer in natural convection ?

03 April 2017 4,535 0 View

Enhancement of heat transfer and the volumetric flow rate (m^2/s)

i have finding difficulties to draw volumetric flow rate"Time series of the flow rate cross the center line (x = 0) in the cases with a fin."in cavity with High H.the formula(7) fig.5.please helpme

08 September 2016 1,109 0 View

How to calculate Ti in cavity just with formula

Hi,my work now is on thermal cavity filled water I want to calculate the initial temperature and the change between tc and e delta T = Th-Tc with Ra = 2.08 * 106 and the Prandtl number Pr = 6.98.I...

06 July 2016 2,781 5 View

Hi , how do you calculate T=-1/2 and T=1/2 at sidewalls?

04 May 2016 1,057 2 View

Can anyone suggest a program wich use an open file *.dat and use it in equation in order to get solution of function ?

Hi, I want to plot Nusselt as function with time and try to suggest how I can do it. if it is possible reguards

01 January 1970 3,169 1 View

Can you send me your article?

Hi, Iw'd like receive your article as pdf in mail:[email protected] Tk

01 January 1970 6,825 0 View

Please, link for films cooling?

Hi,everyone I would like the one of you my cheres to send me articles or link for films cooling.

01 January 1970 8,351 0 View

Some article about the vorticity and vortex please?

01 January 1970 8,400 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View