Can anyone send me article talking about CFX code and relation with thermal fluid?

04 May 2017 8,494 0 View

Can I submitted in thermal energy?

04 May 2017 8,475 2 View

Enhancement of heat transfer and the volumetric flow rate (m^2/s)

i have finding difficulties to draw volumetric flow rate"Time series of the flow rate cross the center line (x = 0) in the cases with a fin."in cavity with High H.the formula(7) fig.5.please helpme

08 September 2016 1,109 0 View

How to calculate Ti in cavity just with formula

Hi,my work now is on thermal cavity filled water I want to calculate the initial temperature and the change between tc and e delta T = Th-Tc with Ra = 2.08 * 106 and the Prandtl number Pr = 6.98.I...

06 July 2016 2,781 5 View

Hi , how do you calculate T=-1/2 and T=1/2 at sidewalls?

04 May 2016 1,057 2 View

Can anyone suggest a program wich use an open file *.dat and use it in equation in order to get solution of function ?

Hi, I want to plot Nusselt as function with time and try to suggest how I can do it. if it is possible reguards

01 January 1970 3,169 1 View

Can you send me your article?

Hi, Iw'd like receive your article as pdf in mail:[email protected] Tk

01 January 1970 6,825 0 View

Please, link for films cooling?

Hi,everyone I would like the one of you my cheres to send me articles or link for films cooling.

01 January 1970 8,351 0 View

Some article about the vorticity and vortex please?

01 January 1970 8,400 1 View

Can I submitted in thermal energy?

01 January 1970 8,227 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View