How to mesh the area with area number in ANSYS APDL?

Rodda KIRAN KUMAR Reddy @Rodda-Reddy

23 August 2019 1 6K Report

Did any one know about how to mesh the area, If the area number is known. It is help in complex structures.

Badges
Science topic

More Rodda KIRAN KUMAR Reddy's questions See All

Dear all, Iam currently working on Dc Microgrid model for electrical vehicle charging. Can any body give good IEEE research paper on this topic?

please give any suggestion?

04 February 2021 4,837 5 View

What does the change in D-peak position in Raman spectroscopy of carbon materials indicates?

We have carried out high-pressure Raman characterization on some of our samples. After fitting, I have observed a change in D-peak position with increasing pressure. What does this change...

20 January 2021 853 3 View

PSFB control signal?

Hi everyone iam facing a problem to give control signal for switches in design of PSFB converter in matlab simulink. Anybody's help will be appreciated.

14 December 2020 6,021 3 View

What are the alternative to the pozzolanic materials to in concrete to enhance the durability of concrete?

As of now, Only industrial wastes were using as pozzolanic materials in concrete to enhance the durability of concrete. Can any once suggest me the alternatives of those materials?

11 October 2020 3,569 4 View

Can any one suggest me the dielectric constant of Gold and Co3O4 at room temperature ?

i have a question regarding dielectric constant of gold,cobalt oxide (co3O4) and n-tpe silicon . i find only one publication on this issue showing dielectric function cobalt oxide(CoO) 12.9 and...

02 October 2020 9,138 4 View

Eupergit beads for enzyme immobilization?

We are looking to immobilize some of our enzymes on Eupergit beads. I was wondering if you know any commercial supplier of Eupergit beads?

28 September 2020 5,664 3 View

Can somebody kindly suggest a good FEM software for the numerical solution of stochastic PDEs?

Please kindly suggest some good FEM softwares for the numerical solution of both time-dependent and time-independent stochastic PDEs.

28 September 2020 6,598 4 View

How to run Seismic analysis for the following model in OpenSees..?

I have developed a 3 bay 5 story 2D frame in Opensees but I have problems with element load and application of seismic load in Opensees using an acceleration file. I always got an error namely...

27 September 2020 5,885 4 View

How can we evaluate the conductance of a constant power load (CPL)?

Any CPL is modeled with a current source in parallel with negative resistance. How do we evaluate the negative resistance, if we know the constant power consumed by the load?

19 September 2020 6,188 3 View

How to learn the modelling of RC beam subjected to 4 point bending in Ansys Mechanical APDL?

I need to model a reinforced concrete beam subjected to 4 point bending. I also need to plot the load vs displacement at mid span and compare it with the experimental data. Bond between concrete...

10 September 2020 9,004 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View