Guys I'm new in abaqus and I have some problems.I am struggling to mesh a flanged pipe.I know that I have to create partitions but I can not do it.Any suggestions?
Really, It's valuable question
Thank you
So,do you know how to help me?
do you make the circular parts on the front, the back and the top of the shape in the picture separately and then assembled it?
Dear Spyros Asrva
I hope this will help you
watch this videos still end.
https://www.youtube.com/watch?v=Vuag2o2dGuU&list=PLNJWOLwOVUNyuoEZEP0t4WUV3mSBHh-z4
https://www.youtube.com/watch?v=XA1YpR_ABJk
I watches these videos but I still struggle to do it
Hamza M. Salman no. Not separately all in once using these planes
During the fabrication of CsPbI3 LEDs with ZnO as ETL and TFB as HTL, I deposited Au on top of the TFB layer. However, upon measuring the devices, there was no photoresponse observed. Is it...
02 May 2024 4,741 1 View
Dear Everyone, I am new to the concept of material science. I tried to simulate a solidification process of 7079 alluminium alloy using Scheil-Gulliver method in Matcalc. However, I noticed that...
01 February 2024 6,976 1 View
I have created a solid mesh of a flange model in hypermesh. However, only one of the mesh quality criteria is not satisfied. The max angle of some hexahendral elements is slightly higher than 135°...
23 November 2022 5,572 3 View
I am new to Gmsh and I have a problem on how to find the boundary nodes from mesh file.My mesh file and model are given below.
03 May 2020 6,996 1 View
I am studying a 2D model for ideal plastic case.I am confused why different element size gives different results,I know that more elements give better results but at least the results should be...
08 September 2019 905 9 View
I am planning to LC/MS experiment to characterize the proteome of a specific biological fluid. I am mainly focused on detecting specific cleaved isoforms of my protein of interest. Is there any...
31 March 2019 9,998 3 View
Does hourglass instabilities exists in a Q4 elements with reduce integration using 2 Gaus points?
19 February 2019 6,167 7 View
Sorry for my silly qustion but I am a little bit confused on how to determine load vecto in fem.My question is when do we include reaction forces in nodes to our load matrix? For example in this...
26 January 2019 4,163 0 View
My question is how to increase the continuity of displacements in case of truss or plane elements. For example from C0 continuity to C1.Is this possible?
22 January 2019 5,662 4 View
Hey guys I want to ask a question regarding the BC's on this pipe.Should I fix only the face of the flanges or the whole flange?Also,should I fix the bolt holes? Thank you very much
12 January 2019 3,587 1 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View