How to mark tiny (0.001 mm dot on stainless steel) dot on steel?

More Varadaraju Magesh's questions See All

How to mesh without obsolete mesh of a skull with teeth, bones, bracket and archwire assembly? Also how to do convergence of this? Ansys workbench?

Have to do perfect error free mesh of a maxilla with cortical, cancellous, orthodontic brackets, archwire etc with contact in Ansys workbench. How to check mesh quality with convergence as well.

28 February 2024 7,266 0 View

Anybody suggest Pan-HCV and Pan-HBV for PCR control purpose?

Hi to all, Does anybody suggest Pan-HCV and Pan-HBV for conventional and real-time PCR-positive control purposes? Due to viral instability, we are unable to use the known positive samples for...

06 February 2024 4,362 3 View

Any correlation between HBeAg and HBV PCR, is this reciprocal?

Statement 1: we got one sample to have HBeAg ELISA and HBV PCR both Positive, indicating active replication present in the HBV virus. Statement 2: we got one sample to have HBeAg ELISA negative,...

06 February 2024 1,594 2 View

What is the crop coefficient of high yielding coconut palms at spacing of 7.6X7.6 m?

Need the crop coefficient of coconut palms to arrive at the irrigation water (ETc)requirement. Does the irrigation water quality affect the crop coeffecient of a crop.

07 May 2020 8,142 0 View

Will coconut palms grow in highly saline coastal soils ?. What is the maximum soil EC coconut palms tolerate?

Need to understand if coconut palms can be grown in coastal soils with pH 7.5 and salinity ranging from 86 to 140 ds/m and high calcium carbonate content?

07 May 2020 3,246 0 View

Principal Componenet Analysis for 3D matrix code in java?

I am having Hyperspectral data. 10 x 10 x 2151(x,y,z axis).For this i have to do PCA, in that process i have to reduce Z axis (2151) in java code.any code available pls suggest

21 November 2019 932 0 View

How can avoid penetration of contact surfaces in ansys apdl, Contacts were created in Hypermesh.

When we twist a bar inside a slot bar had contact on slot walls. Problem is bar is penetrating inside the wall. How to avoid. Contacts were made in Hypermesh, analysis done in ansys apdl.

09 September 2016 2,590 3 View

Why am I getting deflection after applied zero force in ansys transient analysis during elastic stage instead of zero deflection?

I did multiple load steps with ansys transient, after some time when i applied zero force, my model gives some deflection, but within elastic limit, i think that deflection (DMX) should be zero,...

21 September 2015 8,903 6 View

How can I proliferate HCV in cell lines by the feasible technique?

In my research work, i want to study about anticancer activity by using certain herbal extracts with HCV. Mostly researchers using cloning techniques only but i need any other simple and feasible...

06 July 2015 8,571 3 View

Can you suggest how to find a model is subjected to plastic deformation based on ansys results?

I have ansys results of my model. I wish to know whether plastic deformation happens in the model due to force.

17 June 2015 7,461 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

Why did the simulated load-displacement curve of beam keep increasing and didn't decrease (ABAQUS)?

Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...

29 June 2024 6,192 2 View

Methods of measuring the moisture content of iron pellets and iron concentrate in the steel industry?

Dear colleagues, I'm researching some methods of measuring the moisture of iron pellets and iron concentrate in the steel industry (especially non-contact methods). If you have any information...

22 June 2024 7,894 2 View

Paul Rosemann

Hi!

One possibility is to use micro hardness indents with a indentation force adjusted to the hardness of your sample!

Good luck!

Eric Ancich

Have you considered using a laser to etch the surface?

Varadaraju Magesh

No sir, You mean laser engraving?

Yes, you could call the technique laser engraving. But I understand you only want a micron size dot.

Thanks sir. I want micron size dot only as a reference for measurement.

Thank you sir. I will see.