How to import mimics file to ANSYS workbench?

More Reem Yassine's questions See All

If i want to do my research data analysis what i should start with?

like a guide especially with putting the score for my survey. *my survey will measure knowledge level for the disease population Moreover, then which tool should I use? My study is a...

18 January 2021 3,819 10 View

Can I use 24 wells black tissue culture uncoated plate for cultuing macrophage (THP-1 treated with PMA) ?or I have to coat them?

Hello, I will start an experiment using macrophage (THP-1 treated with PMA). I have ordered the plate that suitable for fluorescence plate reader which is glass 24 wells black uncoated tissue...

05 January 2021 4,214 3 View

Which approach and tests for statistical spheroid characterization ?

hello, I'm trying to find a well defined protocol to asses spheroid growth during a period. I want to characterize diameter evolution first, then compare with another medium composition ....

24 December 2020 9,546 5 View

How to estimate prediction bound (interval) ?

Prediction bounds are relatively important when an interval considering the error of the regression model and not only sampling error comparing to the confidence interval.

13 December 2020 8,617 4 View

What is the ideal cell number for detection of HIF using ELISA ?

Hi All, I am planning to measure HIF expression with different cellular conditions using ELISA kit, from your experience what is the ideal number of cells used for this type of experiment?

07 December 2020 3,066 3 View

Why I got different sizes with polyacrylamide nanoparticles when I measure the size by DLS? I've prepared them with same procedure?

I've prepared nanoparticles by inverse microemulsion technique and I've functionalised the nanoparticles with N-(3-aminopropyl)-methacrylamide (APMA) (+ve charge) to facilitate cellular delivery,...

02 December 2020 8,329 3 View

My protein ladder is diffused and take a lot of time for running electrophrosis?

hello, I am doing western blot for cancer cell and my protein ladder diffused during running electrophoresis and the sample is disappear. also it takes too much time more than 3 hr for migration....

14 September 2020 5,113 4 View

How can I quantitatively analyze a sample with carbohydrate content?

Can anyone -who may have hands-on experience in analytical chemistry or photochemistry- help me how can I quantitatively analyze a sample with carbohydrate content?

09 July 2020 3,663 2 View

How to avoid 3D spheres collapsing after fixation ?

Hello everyone, i'm trying to generate 3d spheres of mesenchymal stem cells. when i had to perform ICC, trasferred my spheres into a plastic dish , i let them settle down till they attached. i...

07 July 2020 8,862 8 View

How can i calculate the effective mass of electron and hole for perovskite materials from Wien2k calculations (DFT) ?

I have generated the band structure of my material using Wien2k software , Please could you explain me how we can calculate the effective mass of electron and hole for perovskite materials...

01 June 2020 604 6 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Ehsan Shahabi

hi Reem,when you import from solid works or catia or other software,you should add material propeties. if you dont know hw to do please tell me to send some pictures.

Oguzhan Yalcin

You should check the link.

http://uc.materialise.com/mimics/node/1831

Reem Yassine

Dear Ehsan; i already did assign materials using mimics, but the problem is i cant find the assigned materials in the ANSYS workbench after importing the model.

Dear Oguzhan; could you illustrate more.