How to give relative humidity input in ANSYS FLUENT?

More Raveesh Gopalakrishnan's questions See All

Problem with PCR using plasmid as template?

Hi I am trying to do a PCR for a 1kb fragment using a plasmid of 11kb as a template. But unfortunately on the gel, the band is as large as the plasmid, that is 11kb. Would anyone know that that...

20 October 2020 7,631 3 View

How the saturation temperature is to be provided in evaporation condensation model in ANSYS FLUENT?

I am planning to simulate condensation of moist air in ANSYS FLUENT. Say the inlet conditions of air is at 30 degree Celsius and relative humidity 80%. While giving mass transfer mechanism in...

09 August 2020 7,744 3 View

How to give relative humidity input in ANSYS FLUENT?

I am trying to simulate the condensation of moist air in ANSYS FLUENT. Say, the inlet temperature of air is 30 degree Celsius with relative humidity 80%. I assume that species transport model is...

03 August 2020 211 3 View

Can anyone suggest a way to overcome recombination when amplifying a pcDNA3 plasmid containing human SCN9A CDS insert?

I need to amplify a pcDNA3 plasmid containing human SCN9A CDS insert (pcDNA3-SCN9A construct). The CDS is around 6 kb, and the total construct length is approximately 11.2 kb, which is a bit...

07 June 2020 2,134 2 View

How elementary particles acquire mass and charge?

Elementary particles have their own mass and charge. Mass is known to be acquired by the Higgs field. How charge is acquired by a particle?. Is both the phenomena are dependent?.

08 June 2019 9,722 13 View

How to give initial values of Turbulent parameters in SST K-w model in Ansys Fluent?

I am planning to simulate a natural circulation loop dynamics in Ansys Fluent. The fluid (water) in the loop is initially at rest and initiates flow upon heating at a section. For such a system...

09 January 2019 5,053 5 View

I am planning to simulate a natural circulation loop in ANSYS FLUENT. Which Turbulence model should I use?

The loop diameter is 20 mm and flow will be initially at rest. After giving heat flux, the flow will initiate slowly. From literature review, many researchers have used RNG k-epsilon model as it...

17 November 2018 9,927 4 View

How to generating LDPC parity-check matrices in MATLAB [depend to length of my code-word] ?

How to generating LDPC parity-check matrices in MATLAB [depend to length of my code-word] ? I want to generate different coderate : 1/2, 1/3 and 3/4 using matlab.

22 September 2018 4,701 2 View

What is good negative control cell for S100 marker?

I tried even the primary rat fibroblast but it was positive for S100. Most of the cell lines were positive too. So, I would like to know what is the good negative control for S100...

30 January 2018 9,589 3 View

Should I reconsider the fitting model if I got dissimilar thicknesses for polymer films on Si wafer at multiple angles of incidence?

While measuring the thickness of polymer thin film on Silicon wafer using spectroscopic ellipsometry, I am getting a thickness of 50 nm at 65 deg, 120 nm at 70 deg and 125 nm at 75 degree, for the...

05 January 2015 7,440 6 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View