How to get stresses on any arbitrary/inclined plane in ANSYS APDL?

12 May 2025 0 7K Report

How to get the stresses (normal or shear) on any arbitrary/inclined (non-principal) plane in ANSYS APDL?

Example: To find the bending stress at different points of a 3D initially curved beam modelled with SOLID186 elements.

Badges
Science topic

More Tamonash Jana's questions See All

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

I encountered a situation where the 16s PCR amplification worked perfectly with the DNA from the same sample, but using the same sample Don't working?

I isolated microbial DNA from marine water samples taken at various sites using the Qiagen Power Water DNA Isolation Kit, including a modified enzymatic lysis step. I encountered a situation where...

24 July 2024 9,688 0 View

What is your view point regarding the edible coating on the green leafy vegetables?

1. Nutritional contribution of the edible coating 2. Self life of the vegetable to be coated with the edible coating. 3. Toxicity development after preserving the vegetable with the edible coating.

11 June 2024 1,740 3 View

During ws2 growth via cvd I have noticed black round spots on the si(100) substrate. please suggest me reason behind this?

I am using 20 mg of WO3, 800 mg of Sulphur, 925 oc growth temp, 280 oc S temp, and a 20 sccm gas flow rate.

05 May 2024 8,665 2 View

Can I allow cell phones in SPF animal house?

I have questions regarding the safe use of cell phones in animal research facilities. While I acknowledge the hygienic risk, we often spend a lot of time inside our barrier SPF facility and we...

14 April 2024 3,486 0 View

Inquiry Regarding Research on Female Sex Tourism in Jamaica?

Ladies and Gentleman, My name is Jana Maric, and I am a tourism management student at the university of applied sciences in Germany currently researching for my bachelor´s thesis in the field of...

08 April 2024 4,449 0 View

Can you find this relation ((β²+α²)/2αβ)sinh βb sin αa + cosh βb cos αa = cos k(a+b) from given determinant?

Please do it by hand, if not possible just do by some analytic engine.

26 March 2024 2,028 0 View

Why did I get the cracks on thin film after annealing? And how can I overcome this problem?

I deposited Ga2O3 thin film on fused quartz substrate at 500oc in Ar ambient by RF sputtering and then annealed at 900oc (very slow heating and very slow cooling i.e 1oc/min) in air ambient for 1...

11 February 2024 3,417 4 View

How to incorporate the negative slope (necking) part of an experimental tensile test data in ANSYS?

ANSYS multilinear material model does not support plastic strain vs stress data with a negative slope. Moreover, it assumes perfectly plastic (horizontal) behaviour from the end data point. How...

01 February 2024 9,950 0 View

Regarding UGC care list journal?

INDIAN JOURNAL OF NATURAL SCIENCES ISSN: 0976-0997 ( Print, Bimonthly ) Multidisciplinary Sciences Web of Science Indexes: Zoological Record is this journal UGC care list II category?

25 December 2023 4,017 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What is the role of oxidative stress in toxin-induced carcinogenesis?

What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...

02 August 2024 3,174 1 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Could GSH level be more in CCL4 rats than negative control rats?

i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....

26 July 2024 1,887 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

How do nutrient transporters and aquaporins interact under abiotic stress in plants?

"The Correlation between Nutrition and Transport Mechanism under Abiotic Stress in Plants: A Comprehensive Review" by Muhammad Saleem, Jianhua Zhang, Muhammad Qasim, Rashid Iqbal, and Li Song,...

23 July 2024 9,109 0 View