How to get copper complex crystals? The complex is soluble in both DCM & MeOH medium. Layering technique was done in both DCM/Hexane and MeOH/Ether?

02 February 2018 1 6K Report

the ligand is crystalline in nature.

Disolve in DMSO at saturation and leave it for at least 1 week. Try also different solvent combination and temperature ramping, up and down.

Badges
Science topic

More Sourav Bej's questions See All

Is there any research paper where 1H-NMR data of HCN is provided?

1H-NMR data of HCN is required

08 September 2019 4,558 1 View

What is the role of adding sodium tetrahydro borate in a synthesis module which incorporates an amine part and an aldehyde part?

Is addition of Sodium tetrahydro borate exothermic?

10 November 2018 1,037 8 View

Which software produces pictures like below attached file? I have a MOF entrapping some molecule. I want this kind of picture?

Pictures with and without the molecule are needed.

10 November 2018 4,603 0 View

Is it possible to explain the increase in intensity of photo luminescence with the help of dipole moment?

It is basically related to the sensing of an analyte by MOF .

07 August 2017 6,671 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

What is the best solvent to remove PDMS from nano particles?

I want to remove PDMS oligomers from the surface of nanolayers. I have just read a very helpful paper about the compatibility of PDMS with different solvents( Solvent Compatibility of...

24 February 2021 7,845 5 View

Do you kow of any database containing data on retention time, log P and polarizability for a large number of molecules?

Hi, I am a chemistry undergraduate doing my dissertation project on HPLC. In my project, I need to predict the HPLC retention time of 20 aromatic molecules, the calibration set. To do this I will...

24 February 2021 2,602 1 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

How to seperate PEG-4000 from aqueuse phase ?

Hello everyone , Please tell me if It possible to seperat POlyethelyn glycol -4000 from an aqueuse media by other ways rather heating . I have tried salting out by electrolyte solution to...

22 February 2021 7,285 5 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Questio regarding micro/nano particles fabrication ?

I will start to fabricate micro/nanoparticles for growth factor release and I check out a procedure quite nice, however, it is lacking some details and since I don't have much knowledge doing this...

20 February 2021 199 2 View