I get this error when I define material properties as nonlinear elastic
TB,MELAS
I cannot graph or plot the table.
Have you got a solution to this problem?
Yuhang Ding, I only faced this issue in ANSYS 22.
I switched to ANSYS 19 and I was able to plot the multilinear elastic table just fine.
Hello everyone, I want to plot the stress path on the nodes attached to a shell element using PATH OPERATIONS. The path from ANSYS shows the results at the top of the shell ONLY and not at the...
17 October 2021 4,814 2 View
Dear Researchers, I hope you are all doing well, I have a structure having inclined BEAM188 elements and I am using the element table to find axial stresses in members. Element table ->...
22 August 2021 5,072 1 View
My first picture shows my current mesh size along the direction of the thickness of my SOLID185 element. how can I have more divisions / mesh along the direction of thickness as my second picture...
17 August 2021 6,597 6 View
In the stress results, I get two stress values for the same node and the following error " BEAM/PIPE elements are detected in the selected element set. They are ignored in the nodal averaging...
08 August 2021 3,005 6 View
I modeled a concrete deck slab on top of steel girders in ANSYS APDL but my results for the bending stress (X component stress) from ANSYS do not match what I obtained from hand calculations Using...
06 August 2021 5,389 7 View
When I define the beam cross section and give it b and h dimensions, I notice that ANSYS switches the b and h after i mesh and assign the element it switches the height with the width and vice...
05 August 2021 1,580 3 View
Hi, as seen in the picture I am trying to create a contact pair (Contact / target) between a solid and shell element but I only get flexible connection for the option.
24 July 2021 9,659 1 View
Hi All, l am modeling a composite slab on girder bridge on ANSYS APDL following the shown procedure. I connected the shell element slab to the beam by using MPC184 rigid links. All of my...
24 July 2021 7,739 4 View
Hi, I get an error saying that my model is not sufficiently constrained when I connect solid element having 3 degrees of freedom to a shell / beam element having 6 degrees of freedom. Is there...
18 July 2021 1,058 3 View
I am not sure whether to use boolean A glue command to glue the areas / lines of my model together. OR just use merging nodes NUMMRG, node command My model is a static linear bridge element...
27 June 2021 535 3 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!
08 August 2024 6,242 2 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View