Hi, I saw some of the paper mentions Cd mean and Cl rms coefficients, I dont know how to switch in ANSYS fluent. help me to switch or please explain about it. I attached a image for your refernce ( model lenght Vs Cl rms).
If your simulation is steady simulation, you will have the steady value for the lift coefficient.
If your simulation is transient, you could export the lift coefficient at each time step and calculate the RMS value in Excel.
Is your reference based on experimental or numerical study? could you explain more about your simulation?
its a numerical simulation... And i want to know about Cl mean Vs length. Thank U Mohamed elsakka
Buildings are made of concrete (Strong and stiff) then why wind load are much important for tall buildings. Why builders are looking wind loads on tall building. Can any one explain in detail...
08 September 2018 9,858 0 View
Hello, I am simulating circular cylinder, i want to extract standard deviation of a Cp on a surface, I projected point over the cylinder and i report and save the file in the folder. But my...
07 August 2018 2,684 0 View
I have a question on wind flow around the building using CFD. Why the most of the people are using steady RANS (RANS) models instead of Transient (URANS and LES). The flow will be stochastic...
07 August 2018 4,673 5 View
Hai Every one, I have a question about surface points in ANSYS FLUENT 18. I know I could input the coordinates in the surface->points option. But I have more than 200 points to monitor.it...
03 April 2018 7,942 0 View
Hi, Every one, I am trying to write each time step of pressure coefficent uisng macros in ANSYS FLUENT in my model. After long serach and i found one document (ATTACHED) ,which mentioned like...
03 April 2018 6,246 0 View
i gave my first cell height is 0.0020 accordingly with roughness measurements (0.0019) Ks< first cell height. Can i run this model in LES. ( Model height is 0.7 , width is 0.15m and Domain...
07 August 2017 3,382 3 View
Hi, I want to switch IDDES in fluent. Any one help me to switch this in ANSYS Fluent 16. Looking Forward.
07 August 2016 7,526 0 View
Hi, my analysis is on cables, I found that St = 0.4 in fluent FFT using (Power spectral density) and Frequency is 7.75 Hz. But calculating manually i am getting 0.06 = St. (D=0.155, V= 18 m/s,...
02 March 2016 944 5 View
Hi, I have done DES simulation on tall building structures. In this simulation, Cp[ PRESSURE COEFFICIENT] contours and Graph are showing in negative sign. Is the simulation is correct? Please...
02 March 2016 3,376 7 View
I found some errors creating ABL in Fluent. Just i given a value of roughness 0.4 [m].In wall roughness length. It is correct method to create ABL. Are any method to follow. I request you to...
02 March 2016 9,512 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,723 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...
06 August 2024 6,728 6 View
Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)
05 August 2024 9,537 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View