some edge or face size controls have smaller values than default defeaturing tolerance mesh entities generated with these size control will not defeatured plz solve this problem
Buildings are made of concrete (Strong and stiff) then why wind load are much important for tall buildings. Why builders are looking wind loads on tall building. Can any one explain in detail...
08 September 2018 9,858 0 View
Hello, I am simulating circular cylinder, i want to extract standard deviation of a Cp on a surface, I projected point over the cylinder and i report and save the file in the folder. But my...
07 August 2018 2,684 0 View
I have a question on wind flow around the building using CFD. Why the most of the people are using steady RANS (RANS) models instead of Transient (URANS and LES). The flow will be stochastic...
07 August 2018 4,673 5 View
Hai Every one, I have a question about surface points in ANSYS FLUENT 18. I know I could input the coordinates in the surface->points option. But I have more than 200 points to monitor.it...
03 April 2018 7,942 0 View
Hi, Every one, I am trying to write each time step of pressure coefficent uisng macros in ANSYS FLUENT in my model. After long serach and i found one document (ATTACHED) ,which mentioned like...
03 April 2018 6,246 0 View
i gave my first cell height is 0.0020 accordingly with roughness measurements (0.0019) Ks< first cell height. Can i run this model in LES. ( Model height is 0.7 , width is 0.15m and Domain...
07 August 2017 3,382 3 View
Hi, I saw some of the paper mentions Cd mean and Cl rms coefficients, I dont know how to switch in ANSYS fluent. help me to switch or please explain about it. I attached a image for your refernce...
09 October 2016 9,465 2 View
Hi, I want to switch IDDES in fluent. Any one help me to switch this in ANSYS Fluent 16. Looking Forward.
07 August 2016 7,526 0 View
Hi, my analysis is on cables, I found that St = 0.4 in fluent FFT using (Power spectral density) and Frequency is 7.75 Hz. But calculating manually i am getting 0.06 = St. (D=0.155, V= 18 m/s,...
02 March 2016 944 5 View
Hi, I have done DES simulation on tall building structures. In this simulation, Cp[ PRESSURE COEFFICIENT] contours and Graph are showing in negative sign. Is the simulation is correct? Please...
02 March 2016 3,376 7 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...
08 August 2024 4,645 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Hello researchers, Sorry for my stupid question. I am learning the QIIME2 workflow for analyzing some 16s amplicon NGS fastq data. I found a very nice paper with data and code public available...
20 July 2024 5,405 2 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
How is biomass energy essential in the power generation in a country.
08 July 2024 9,477 2 View