I want to simulate heat pipe in fluent with 2D geometry ?? what is procedure ?
will you provide some link of tutorial
Hi, Simulation of a wicked heat pipe is very challenging in Fluent using the current VOF models because of the additional burden of Darcian wick transport. Wickless heatpipes(thermosyphons) can be simulated by employing the VOF model
see:
http://www.sciencedirect.com/science/article/pii/S1359431113004699
Good luck!
I am unable to get the hourly solar radiation data of my study area Mumbai, Maharashtra. How can I get hourly solar insolation data of Mumbai, India?
10 November 2018 6,666 12 View
Dear friends I am simulating diffuser with changing divergence angle to check the pressure coefficient If we compare the experimental and computational value, they are not satisfactory. The...
07 August 2017 1,849 4 View
I am doing CFD analysis of waste heat recovery from flue gas to remove moisture content from coal particle. I think This is problem regarding Discrete Particle Method In fluent. But Hoe to add...
02 March 2017 6,892 2 View
I want to simulate cyclone separator with discrete phase and moisture content (evaporation and condensation ) using star ccm. If anybody has tutorial please share it.
01 February 2017 6,066 1 View
we know we can define enthalpy at constant pressure. But what is enthalpy at constant volume? Is enthalpy is equal to internal energy in constant volume process?
10 November 2016 2,918 3 View
I am simulating spray atomizer. Cold Water is rotating through rotating chamber. It comes out as droplet from nozzle.Hot air is coming in contact with water droplet . which model should I use for...
05 June 2016 5,368 8 View
Does any body have fluent(mesh) file of this tutorial? http://dl.racfd.com/tank.pdf
04 May 2016 6,445 2 View
I am trying to simulate rotating spray dryer with water and air as multi phase. I got error in meshing The mesh file exporter failed during translation. Please send your data to your support...
04 May 2016 9,263 3 View
In Ansys workbench we can split face using tool is it possible to split body in ansys workbench? If yes , how?
04 May 2016 2,709 8 View
I am simulating radiator with water as hot fluid and air cooling fluid. water is flowing through tube and air is flowing around tube(like cross heat exchanger). BC Water inlet - mass flow rate...
04 May 2016 9,526 3 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,027 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,987 3 View
To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...
06 August 2024 6,726 6 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 946 1 View
Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)
05 August 2024 9,537 2 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,535 1 View
Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...
31 July 2024 3,332 4 View
We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...
31 July 2024 4,509 3 View
Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...
29 July 2024 8,622 1 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,982 1 View