12 October 2021 4 6K Report

Hello,

I need to know how to to design Butterworth filter with different insertion loss values. Regarding butterworth(Maximally flat) formula or table, they are obtained for insertion loss 3dB. I need to define the filter element's value based on different values of insertion loss.

More John Jin's questions See All
In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Similar questions and discussions
What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

How to calculate Total Flavonoid?

I analyzed flavonoid total spectrophotometry, the procedure as below: 2 ml supernatan added 5 ml dd.H2O, then added 0,15 ml NaNO2 5%, 5 minutes later added 0,15 ml AlCl3 10%, After 6 minutes,...

01 March 2021 6,722 1 View

RNA-seq DEGs downstream analysis and reporting in literature?

I used EdgeR to get the list of DEGs (differentially expressed genes) from my liver RNA-seq experiment. I have done the gene overrepresentation and GSEA based pathway analysis. I am currently...

23 February 2021 8,969 1 View

What are the ranges of four diffterent poles of butterworth filter for ECG signal?

Hi, Can anyone please tell me what are the ranges of four different pole orders such as first order, second order, third order and fourth order respectively of butterworth filter for ECG...

23 February 2021 2,554 3 View

Which polarizers are usually used to measure the birefringence of zebrafish muscles?

I already found several publications on that topic, however, the specifications for the used filters are often missing. Some more specific information than "fish is placed between to polarizing...

23 February 2021 1,934 1 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Is it possible, for a limited dateset of images, to use Convolution filters + Random Forest instead of UNet?

UNet is 'relatively' recent and was invented mainly to deal with biomedical images, yet is it also possible, for a limited dateset of images, to use Convolution filters + Random Forest instead of...

21 February 2021 4,858 3 View

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

Algorithms to filter corrective max and min from a set of data?

I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...

17 February 2021 2,777 5 View

Why ICP-MS test for Teflon filters that collected PM2.5, show really high results in the millions of ug/g ?

I analyzed soil and ash samples using ICP-MS for 28 metals, then I resuspended those samples to collect PM2.5 particles in a filter using a selective inlet inlet. My only issue that Fe and Al...

13 February 2021 7,592 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close