How to create a zero thickness wall in ansys workbench?

12 December 2015 0 3K Report

Hi,

I have a 3D geometry with a duct wall (image attached).

Now for 2D geometry , I can very easily use imprint face option and create a wall but in 3D, I do not know how to do it.

I tried many things like body operations-> imprint faces, slice etc but none of them are working.

I know surface geometry does not work with 3D but is there a way I can achieve this or do I need to then give some thickness to the duct wall .

Thanks

Badges
Science topic

More Shashank Mishra's questions See All

Can someone help me prove the approximate coefficient of numerical diffusion?

Hi, Can someone please help me with deriving that false/numerical/artificial diffusion is flow direction dependent and it is given as (image attached). also as per Patankar book , numerical...

09 October 2016 2,989 12 View

Why the disturbance diffuses to larger distance if we have fluid at rest with low viscosity compared to fluid with high viscosity?

The throwing of a stone in a lake (can be approximated as hydrostatic case) creates ripples in the water. The ripples or the disturbance associated with this is elliptical and travels uniformly in...

07 August 2016 1,073 4 View

How to impose initial condition on vorticity if solving NS equation in primitive variables ?

05 June 2016 1,434 5 View

How to implement dual time technique in CFD?

Hi, if solving an incompressible flow using ACM method, for time dependent cases, we need to use dual time technique. Can some one explain me for example if I want to solve a simple question...

03 April 2016 8,992 3 View

Why re-circulation / separation results into an increase in drag?

11 December 2015 5,251 13 View

What is the boundary condition for pressure gradient at outlet of a fully developed flow in a rectangular channel?

09 October 2015 9,702 2 View

Why Ansys fluent Inviscid model is not getting converged for simple duct problem?

09 October 2015 4,506 7 View

Is sliding mesh or dynamic mesh more appropriate for CFD simulation of high speed train?

08 September 2015 3,458 10 View

Can anyone help with simple MHD simulation setup in Fluent?

07 August 2015 442 7 View

What should be the boundary condition for primitive variables if solving flow in a duct?

07 August 2015 3,779 7 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View