How to coat Graphene on ITO/GC ?

More Muthusankar Eswaran's questions See All

What is the current trending analytes for the micro extraction techniques based on LC-MS/HPLC/GC?

Hai All, What is the current trending analytes for the micro extraction techniques based on LC-MS/HPLC/GC? and which analyte (food or water) is still to explore which will be very useful to the...

31 December 2018 733 4 View

I need to coat graphene on Glassy carbon electrodes for electrochemical studies?

Dear All, I've synthesized Graphene by hummer method and want to use it for electrochemical studies. Since graphene has no functional group in it. How Can I coat it over GC or directly drop cast...

02 March 2018 5,414 3 View

How to stabilize glassy carbon electrode (GCE)? and how to clean it?

Hai All, How to stabilize glassy carbon electrode? During my experiment it is keep on giving noise peak. How can I reduce it. Also how to clean GCE after experiment.

01 February 2018 845 0 View

Solvent to solubilize Diphenylamine?

Actuall I'm doing electrochemical analysis for Diphenylamine. In HCl diphenylamine's solubility is very less. What are all the other solvent I can use for this purpose?

01 February 2018 9,345 3 View

Hai all, Can anyone tell how to make a gas sensor in laboratory (simple setup)?

09 October 2016 1,000 4 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

Samira Naghdi

Vacuum-filtration method is a simple method for producing thin film of graphene or graphene oxide. First you need to disperse your sample (graphene in your experiment) in a proper solvent. After making a thin film via vacuum filtration you can transfer the thin film on any types of substrate (solid or flexible) you want.

Moreover, using other simple solution-based deposition methods such as spray-coating and spin-coating would be helpful.

Muthusankar Eswaran

Thanks all.

Alexander Pud

You could try electrodeposition method

Article Direct electrodeposition of reduced graphene oxide on glassy...

Conference Paper ELECTRODEPOSITION OF GRAPHENE ON SILICON FOR BIOSENSING APPLICATION

https://www.nature.com/articles/s41598-017-14200-7

Article Direct Electrodeposition of Graphene Enabling the One‐Step S...

Thank u sir @ Alexander Pud .