How to stabilize glassy carbon electrode (GCE)? and how to clean it?

Muthusankar Eswaran @Muthusankar_Eswaran

02 February 2018 0 952 Report

Hai All,

How to stabilize glassy carbon electrode? During my experiment it is keep on giving noise peak. How can I reduce it. Also how to clean GCE after experiment.

Badges
Science topic

More Muthusankar Eswaran's questions See All

What is the current trending analytes for the micro extraction techniques based on LC-MS/HPLC/GC?

Hai All, What is the current trending analytes for the micro extraction techniques based on LC-MS/HPLC/GC? and which analyte (food or water) is still to explore which will be very useful to the...

31 December 2018 775 4 View

How to coat Graphene on ITO/GC ?

Hello All, I've been trying to coat Graphene on ITO/GC. The problem i'm facing is Graphene is not getting coated on the ITO/GC. What kind of electrolyte? as well applied voltage? i have to use to...

04 May 2018 8,964 4 View

I need to coat graphene on Glassy carbon electrodes for electrochemical studies?

Dear All, I've synthesized Graphene by hummer method and want to use it for electrochemical studies. Since graphene has no functional group in it. How Can I coat it over GC or directly drop cast...

02 March 2018 5,452 3 View

Solvent to solubilize Diphenylamine?

Actuall I'm doing electrochemical analysis for Diphenylamine. In HCl diphenylamine's solubility is very less. What are all the other solvent I can use for this purpose?

01 February 2018 9,383 3 View

Hai all, Can anyone tell how to make a gas sensor in laboratory (simple setup)?

09 October 2016 1,042 4 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

Dirty and clean?

Hi everyone I need a file with a dirty and clean potato image

04 August 2024 7,199 4 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

How to clean the CAD detector?

The module of the CAD detector is corona Veo. It has been idle for a long time. And it was not well maintained before idle. I have replaced the gas filters and flushed the system with a 50/50...

01 August 2024 7,805 0 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View