How to capture shock reflection in Starccm+ or Ansys ?

01 January 2018 0 289 Report

During solving CD nozzle, what is the procedure to capture shock wave reflection in Ansys or StarCCM+

Badges
Science topic

More Manigandan Sekar's questions See All

In fluent heat flux analysis results are not converging ?

I had solved the heat flux analysis of the multi-domain problem in fluent. Even after the 20000 iterations also the solution is not converging. As the iterations increase the results are diverging...

10 November 2019 3,972 3 View

How to draft a review paper effectively in short span of time for high impact journals?

Writing a review paper required a lot of effort. Any tactics is there to complete it in short span of time. Especially for Elsevier or reputed journals with high Impact factor.

06 July 2019 2,293 3 View

Do addition of nanopartilces in soil increases the Plant yield ?

Can any one explain me that addition of nanoparticles enhances the growth of plant and produces more yield. If so, can anyone list me the nanoparticles i can use Plant is Tomato and Aubergines

05 June 2019 268 4 View

No title

I came across few having 3 PhD in different fields. Am very confused about this ? Thanks in advance

02 March 2019 7,556 2 View

Is addition and removal of Co-author during submission of revised article is acceptable @Elsevier ?

I like to know the removal, addition and shuffling of co-authors is against moral and ethics in Elsevier Journals. Is it necessary to contact a editor to make such changes

01 February 2019 1,137 15 View

Differences between research papers and technical note of journal?

Can i write an technical note below 1000 words. If not what is the idle limit for them. Is there any mandatory rules

31 December 2018 9,217 1 View

Best way to access recent Engineering Books in online ?

I need to access the book : Energy Efficiency in Air Transportation Published by elsevier. I tried many options but no use. Since i can't afford to buy this, is there any way to access the ebooks

31 December 2018 4,163 4 View

How to solve Blast in FEA ?

What are the boundary conditions are required for blast loading. Share the tutorials if possible.

31 December 2018 1,249 0 View

What is the difference between review track and non review track in Elsevier conference ?

In Elsevier conference there are two options for paper submission Review track and non review track. What is the meaning for that. Will they publish both articles in supporting journal

07 August 2018 3,866 0 View

How to approach Faculty Exchange Program to the foreign Universities ?

Hi Am looking for an Faculty exchange programme vacancy in foreign universities to improve my career in technical fashion. I don't know how to start them. Can anyone guide me

07 August 2018 8,713 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Could anyone tell me what is the range of submillimeter wave?

There is confusion regarding the submillimeter-wave range. Many papers specify its range from 300GHz but some also consider its range from 100GHz. If I design an antenna on 122ghz what would I...

01 March 2021 516 7 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View