How to calculate noise of a fan in CFX ANSYS?

Harrish Sajiv @Harrish_Sajiv

01 January 2016 1 2K Report

based on research i have heard about the macro calculator in cfx

Bala Krishnan

you can use ansys multi physics easily to get the fan noise but it will work very well for the low frequency.

Badges
Science topic

More Harrish Sajiv's questions See All

Mesh convergence study on nozzle?

i am currently doing a mesh convergence study on nozzles. Based on my CFD results, i need to prove why coarse mesh is better then fine mesh. Pls recommend me some articles. it will be helpful for...

02 March 2016 6,055 3 View

Sst turbulence model for different types of shapes(nozzles)?

i need some articles regarding the usage of shear-stress transport model(sst) turbulence model in different types of nozzles(convergent/divergent/both). Pls recommend me.

01 February 2016 7,152 1 View

Shear stress transport turbulence model for different shapes?

it is possible if anyone can recommend me some articles relating using SST turbulence model for different types of shapes where the fan is rotating inside. CFD/CFX/FLUENT

01 February 2016 9,593 2 View

In ANSYS CFX, What are the uses of Sound Pressure level and Sound Pressure level?

Given at 1200rpm the fan speed Sound Power Level : 27.7815dB Sound Pressure Level : 27.7815dB How to calculate the noise?

31 December 2015 7,520 1 View

I am currently doing an analysis on mosquito trap. How can I obtain some fan calculations like Cfm,Flowrate and turbulence within my trap?

Any recommended articles or websites? Assume my computer fan is inside my model. How do i go about the calculations for CFM, Flowrate and Turbulence and the reynolds number. Assume air enters the...

31 December 2015 7,283 1 View

What is the best way to illustrate turbulence of air within a hour-glass model with a fan inside?

Use which contour function and variable? How to calculate turbulence within a trap?(expression?) Software: ANSYS CFX AND FLUENT

31 December 2015 548 1 View

What is the difference between transient analysis and steady-state analysis?

Imagine my fan is spinning in my model. How will it defer in both analysis?

31 December 2015 8,931 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View