Mesh convergence study on nozzle?

02 March 2016 5,980 3 View

Sst turbulence model for different types of shapes(nozzles)?

i need some articles regarding the usage of shear-stress transport model(sst) turbulence model in different types of nozzles(convergent/divergent/both). Pls recommend me.

01 February 2016 7,010 1 View

Shear stress transport turbulence model for different shapes?

it is possible if anyone can recommend me some articles relating using SST turbulence model for different types of shapes where the fan is rotating inside. CFD/CFX/FLUENT

01 February 2016 9,516 2 View

In ANSYS CFX, What are the uses of Sound Pressure level and Sound Pressure level?

31 December 2015 7,411 1 View

What is the best way to illustrate turbulence of air within a hour-glass model with a fan inside?

Use which contour function and variable? How to calculate turbulence within a trap?(expression?) Software: ANSYS CFX AND FLUENT

31 December 2015 472 1 View

How to calculate noise of a fan in CFX ANSYS?

based on research i have heard about the macro calculator in cfx

31 December 2015 2,238 1 View

What is the difference between transient analysis and steady-state analysis?

Imagine my fan is spinning in my model. How will it defer in both analysis?

31 December 2015 8,835 1 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View