How to apply base excitation in ANSYS fluent?

More Abirami Gowriswaran's questions See All

How long does it take to lyophilize 50 ml liquid sample?

Approximate time taken for lyophilization of 50 ml sample mixed in sterile water. Purpose of lyphilization is HPLC. We have Lyodel lyophilizer in our facility. Model: DPRG-1GH? Thanks!

11 September 2019 2,374 2 View

What is the best way to detect extra cellular proteins like perlecan and nidogen from cultured fibroblast using western blot?

Right now I am using 1% NP40 containing lysis buffer to collect the lysate from rabbit corneal fibroblast cells.

22 September 2014 7,249 4 View

Can someone advise on how to calculate improvement rate difference? Or recommend a video tutorial? What is meant by "minimum number of data points removed for total data separation"?

Seeking advise on calculating an effect size using the improvement rate difference (IRD) method

30 June 2013 6,099 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Can you share me how teacher education is managed in your respective national educational system?

I feel that the practice in teacher education in my country is below the expected performance level due to very poor management system. Hope I will learn something from your experiences.

02 March 2021 1,516 4 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View