How to analyze the strength of the wood material on ANSYS APDL?

More Alamsyah Bin Muh. Saleh's questions See All

In DFT or HF, is it more expensive to calculate the H matrix or to diagonalize it?

I was wondering: in common DFT (or Hartree-Fock) algorithms/codes, and in particular in solving the Roothan equation, what is the most computationally expensive part: 1- evaluate all the terms of...

01 February 2021 396 2 View

Warning in Lavaan, variance-covariance not positive definite!, model is not identified?

Dear colleagues, I am new to R, I have been using Amos for conducting CFA but came to learn that when dealing with Likert scale, Lavaan in R is a better tool to do such analysis. I started using...

30 December 2020 5,608 3 View

How can i figure out whether nanoparticles in my synthesis crosslinked or not?

i prepare protein nanoparticles. in one of my synthesis i use trifle amount of crosslinker and the nanoparticles stick in the bottom of plate. how can i understand that nanoparticles become...

03 December 2020 559 8 View

What is the best solver in OpenFOAM to study melt-water interaction?

During a severe accident in a nuclear reactor an energetic molten fuel/coolant interaction could happen, where a multiphase flow of a steam-water mixture in a region which contain drops of a...

29 November 2020 8,376 2 View

How can we define columns in 3D PLAXIS model for buildings existing near the excavation?

I started by a model using 3D PLAXIS to study the effect of deep excavations on existing buildings. The building was simulated as a surface plate with a surface load. Now I'm trying to do it as a...

29 November 2020 3,198 4 View

How to read forces from a file and apply them to a specified nodes in ANSYS APDL?

I want to apply different forces for every node. These force values are saved in .txt or .csv file. Can anybody help me to do that using APDL command. I attached Ansys input file for my model and...

15 November 2020 2,883 1 View

Where can I find off targets for Apis mellifera?

I would like to find off target sites for my sgRNA, however the more commonly used off target finders do not include apis meliifera, is there an application or website that would allow me to do...

09 November 2020 3,463 1 View

What is the best method to sterilize hydroxyapatite nanoparticles?

Powder insoluble

08 November 2020 509 3 View

Wrong cell dimension (cosAB)?

All input files with bravais lattice that contains an angle doesnt run in my Quantum espresso. i even tried running them in my friends laptop but the crash file displays the same problem. i hope...

03 November 2020 2,722 1 View

How Abaqus can generate lumped mass matrix with non zero values only at the diagonal ?

Hi everybody I generated mass matrix by Abaqus, but it has nonzero off diagonal values. I need to get lumped mass matrix with nonzero values only at the diagonal. In Ansys I can turn Lump on...

28 October 2020 5,960 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Alamsyah Bin Muh. Saleh

so and then, how to analyze if this two materials are combined in a single construction?

Assalamualaikum Wr. Wb.

Thanks for attention Mr. Farhad Falakzaadeh from Shiraz University of Technology (Iran)

I also pursue new mechanical structure, if the explanation that you give enough help me, but if there are examples of research in the form of a journal or a paper similar to the case that I was working,???

where can I study and learn to better understand in detail...

We instructions

Thanks,

regards

ABMS

Thanks for suggest Mr. Farhad Falakzaadeh, i will try...

best regards