How to analyze solar pond in ANSYS?

01 January 1970 1 5K Report

Fabricated with MS sheet with tickness of 2mm ans insulated with HDPE and themocole and salt having concentration of 35mg/litre

Veeramanikandan M

dear sathish,

first you design the prototype in any modelling software,

and then you import the prototype in analysis software. My best suggestion for analysis you can try the CFD for solar pond

Badges
Science topic

More Sathish Dhandapani's questions See All

Kindly help me anyone. How photonic crystal influence the antenna characteristics like gain, directivity?

Need a detailed theory regarding, effect of PBG to increase the gain, with less directivity in microstrip patch antenna ...

03 July 2020 4,384 1 View

How to increase the gain and directivity in the microstrip patch antenna?

In CST, while designing the antenna, the antenna parameters return loss and VSWR is good. But the gain and directivity is not attaining as expected level. How to improve this?? Kindly suggest me...

23 June 2020 5,379 11 View

Any Suggestion For Custom Antibody Development?

My lab is currently looking at creating a custom antibody. There aren't a lot of customer reviews on the websites for these things, so what are the companies that you all prefer to synthesize your...

24 April 2020 1,365 4 View

How is hardness of the ceramics measured?

As per the definition, Hardness is the resistance to the deformation. But, deformation can be seen in plastic materials only. ceramics are brittle in nature. So, the material will break when it...

24 January 2020 4,588 3 View

How formalin inactivate microbes ?

Hello everyone I use formalin to inactivate virus. How formalin inactivate virus and other microbes.then how many milli liter of formalin need to be inactivate

01 October 2019 3,391 5 View

Is there any free journals available to publish the review article with in 1 (or) 2 months?

I want to publish my review paper in any reputed journal, but the time duration is less. Are there any free journals available to publish with in 2 months? Otherwise can you list trustworthy paid...

12 March 2019 9,448 31 View

Can the value of Gain RHCP or Gain LHCP be negative?

My antenna is circularly polarized. I want to know whether it is LHCP or RHCP. So, I plotted Gain RHCP vs frequency and Gain LHCP vs frequency graph. I am getting gain in negative value for both...

10 March 2019 5,395 3 View

Where can I find sensor data for Hurricane Florence and Hurricane Michael?

I am looking for sensor data (for eg., Satellite, Remote Sensing etc.,) associated with Hurricane Florence and Hurricane Michael? If you have or pointers to it ... Could you share?

04 March 2019 1,576 3 View

Error in generating Hirshfeld surface?

I have tried to generate hirshfeld surface for an organic molecule. It consists of an water molecule in its crystal lattice. While am trying to generate the surfaces, it shows the following error....

11 April 2018 3,026 2 View

Can any one clarify my doubt regarding Related Substances analysis by HPLC quantification?

Hi, My Compound is an Mesylate salt, I have identified 5 impurities and Synthesized. Out of which three compounds are neutral compounds (i.e not in the form of salts), one compound is mesylate...

24 September 2017 8,073 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View