How to add "remote displacement" type boundary condition in APDL?

More Rashiga Walallawita's questions See All

How to perform multi objective optimization is MATLAB?

Dear all, I have set of results obtained from fea software using a particular DOE. I imported the data using an excel file to MATLAB and used the curve fitting tool to obtain the response...

05 April 2019 3,289 1 View

How to select mean stress correction method for fatigue simulation/analysis?

There are several types of mean stress correction methods in fatigue analysis such as Goodman, Gerber, etc, So for a fatigue analysis what is the basis of selecting a mean stress correction...

20 August 2018 9,284 11 View

How can stress concentration occur on flat contact surfaces?

Hi all, I've being trying to simulate effect of bolt pretension using ANSYS mechanical. The bolt load is 12000 N. I'm using axi-symmetric simulation. The issue is stress concentration is high on...

24 May 2018 1,027 1 View

How to configure ABAQUS solver for ANSYS Mechanical?

Hi, Can any one please let me know how to configure ABAQUS solver for ANSYS workbench? So I can run simulations using ABAQUS solver which are pre-processed in ANSYS. I read the help file, but...

23 January 2018 2,977 3 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Abhishek Deshpande

Hope this helps!

You can figure out by applying 'Remote Displacement' in ANSYS Workbench on a simple problem. Next go to 'Solver Files Directory' and open '.dat' file. It should have all the APDL commands for the operations you performed in Workbench and you will know APDL equivalent of 'Remote Displacement'.

Mir Aamir Abbas

Hi Rashiga Walallawita . You can apply remote displacement by creating a mass element at the location where you want to apply the remote force and then connect it to the supporting area by rigids for rigid behaviour and by RBE3 for deformable behaviour.