How does the N value be counted for gut content analysis?

I read some articles on mollusc and fish diet analysis. The formula for percentage frequency of occurrence stated above: %F0 = Nei/Ne x 100 and percentage numerical abundance : %NI : Ni/N x...

15 October 2020 4,568 3 View

Why is it necessary to vortex and incubate in dark the sample and DPPH solution and other DPPH questions?

Hi all, In the determination of Antioxidant capacity of fruit samples, I used DPPH assay and have a few questions regarding the DPPH assay 1) why is it necessary to vortex and incubate in dark...

30 August 2020 246 3 View

How to renew the Scopus index status of a journal?

Dear Researchers, Our journal (ISSN no. 2070-4658) was part of the Scopus index till 2017. Now, it is not in the Scopus index as the last two years no issue has been published. However, the...

24 August 2020 7,203 3 View

Hello,i extract my plants using rotary evaporator and i got crude extract.How should dilute it?i have no idea on how to dilute it?Can someone helpme?

dilute it in ethanol or dmso? which solution is better as i used 95% of ethanol as my extraction solvent?

23 March 2020 5,971 6 View

Can I set "20 uL reaction volume" in PCR cycler machine, while my actual sample is only 10 or 15 uL?

This is a stupid but quite technical question. We have a PCR machine that has 20 uL minimum reaction, so it can't be set into 15 or 10 uL in the machine. Is this going to affect the result...

22 March 2020 3,497 4 View

Is there any SOP to measure pharmaceutical clean room and if none can we develop our own method to measure the room size?

06 March 2020 866 1 View

How to test degree of polymerisation of aged kraft paper impregnated in oil?

kraft paper was impregnated in mineral oil at different temperatures and duration. my project is to get the DP value at different duration. in order to be measured by viscometer, the sample must...

20 January 2020 2,234 3 View

What is the equation to explain how one possible organic side product is formed in the synthesis of 1-bromobutane?

And show the chemical properties window of this side product. Explain how this product can be separated from the desired product. I have already identified that the possible organic side products...

29 December 2019 6,170 4 View

Validation for Intracerebroventricular Microinjection of Streptozotocin in Rats?

Hi, I'm planning to induce sporadic Alzheimer's disease (AD) in male Sprague Dawley rats (3 months old, 270-350g) through bilateral intracerebroventricular microinjection of 3 mg/kg streptozotocin...

25 November 2019 9,723 3 View

What is the meaning of negative activation energy?

I am prepared (Al, Co) co-doped TiO2 thin films by spray pyrolysis technique. The electrical measurement was performed by the four-probe point method, in the range of temperature 3ok (Room...

22 October 2019 526 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View