we are conducting experiments on pH of different soils. How often do I need to measure the soil pH? Do I need to measure continuously 24 by 7 in 365 days? How often the pH of the soil will change?
Please look at the following below links which may help you in your analysis:
https://vlab.amrita.edu/?sub=2&brch=193&sim=1549&cnt=1
https://clu-in.org/download/ert/1844-r00.pdf
https://www.awri.com.au/wp-content/uploads/v_activity_soil_ph.pdf
Thanks
Thank you so much isam eldin hussein Sir
Depend on the soil, but generally soils have a good buffering capacity.
Moreover,
📷
Therefore, small pH variation requires big variation of H+.
Other question, pH in water or pH in KCl? They measure different properties of the soil:
https://www.researchgate.net/post/Please_tell_me_more_details_why_pH_in_1_M_KCl_is_higher_than_pH_in_water
remember, pH = -log10 [H+]
when we diesign the microstrip antenna we should take the substrate having low dielectric constnat .if we take higher dielectric constnat value then fringing will be less. And also it triggers lot...
04 May 2019 3,896 1 View
04 May 2017 7,240 2 View
After chromium and gold metaliaztion can i do si etching by using TMAH solution.
01 February 2017 6,503 2 View
31 December 2016 6,061 2 View
I am depositing gold by using sputtering on si substrate and i am using cromium as adhesion layer between gold ans si but gold is not at all sticking , what should i do now?
06 July 2016 8,028 8 View
in microelectronics fabrication after liftoff how can i clean metal layers from contaminations.
05 June 2016 7,384 0 View
01 January 1970 5,280 3 View
When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...
03 March 2021 4,892 5 View
Dear colleagues: I would like to know if anyone knows of a database that gives me the parameters pH, K, K, Mg, P, C, N, Zn, Cu, Ni and Cd of common foods. I find a lot of information of proteins,...
26 February 2021 5,525 3 View
The limit test I'm referring to is USP method II. In this procedure you need to dropwise add 6N of NH4OH to the sample until it the pH is alkali. After that you need to dilute and add HOAc until...
23 February 2021 2,049 3 View
I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...
22 February 2021 5,324 3 View
22 February 2021 9,932 11 View
Please suggest solubilisation of chlorobutanol in injections. Tried pH and high temperature. But the issue is of assay drop. If anyone can suggest any solution. Its a commonly used excipient for...
21 February 2021 7,397 1 View
Hello, I am investigating properties of water in oil emulsion explosives. And adding hexamine (hexamethylenetetramine) into one of the phases that are used to make the emulsion should increase the...
21 February 2021 8,680 1 View
I would like to ask what other properties of water (pH and such) shall be analyzed and evaluated to test the effectiveness of activated carbon from filtering the contaminants present in the water?
20 February 2021 9,422 8 View
We want to use phenol pH graphic to measure the pH of mediums before and after inhibitor application to cells. We have phenol absorbence values at 460, 560 and 720 nm wavelength. When we measure...
20 February 2021 7,700 3 View
Peat possess organic content above 75% and is highly acidic in nature (i.e. pH < 4). Before commencing stabilization, it is mandatory to know about the pH level of peat. Therefore, your...
18 February 2021 9,424 7 View