How is the average coefficient of friction calculated?

Gedvidas Bikulcius @Gedvidas-Bikulcius

01 March 2023 0 3K Report

Hello,

It is interesting, how the average coefficient of friction iš calculated and what its physical meaning is.

Sincerely,

Gedvidas Bikulcius

Badges
Science topic

More Gedvidas Bikulcius's questions See All

What aluminum alloys are used in piston production?

Interesting and of piston production methods.

27 May 2024 1,112 3 View

At what is the lowest temperature possible with a synthetic NiS (NiS2) compouds?

Hi everyone, I am especially interested in chemical and electrochemical methods. Thanks.

02 March 2024 8,396 0 View

Where it can be used of NiP black and shiny at the same time?

The coating electrolles of NiP have properties absorbing and speculary at the same time.

21 January 2024 353 1 View

What aluminium oxide pores will absorber more light?

Let us compared Al oxide pores perpendicular to the Al substrate and parallel to each other with patirs not parallel to each other, i. e. irregularly deviated from perpendicular to the substrate....

03 January 2024 3,109 3 View

Is there a relationship between the adhesion of paint-steel obtained by scratch mesh and single scrath methods?

Hello everyone, Adhesion measurements were performed after paint-steel exposure in the NSS (neutral salt spray) chamber. P. S. On of the scratches in the paint coating was done before...

27 September 2023 7,064 0 View

Is have a correlation between the reflection of blackbody and its band-gap?

I am especially intetested inanodized and blackened aluminium and its alloys.

04 September 2023 6,382 2 View

How cold the mechanical properties of flies from divers be measured?

Hello, It is important to choose the best fly divers (source of chitin) at least qualitatively. Thanks Gedvidas

28 March 2023 3,023 1 View

Hello everyone, Maybe someone knows how to blacken aluminium only by anodizing it?

In addition the laight reflection of the oxide layer must not exceed 5 percent. Sincerely, Gedvidas Bikulcius

23 February 2023 8,754 2 View

What methods are used to stop the rate of dissolution of magnesium (its alloy) in physiological solution?

Hello colleagues, It is known that rapid dissolution of orthopedic implants is dangerous. What methods are used to stop the rate of dissolution of magnesium (its alloy) in physiological...

29 September 2020 2,094 5 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

Among Ansys and Abaqus which one is preffered for Modal analysis?

I want to do modal analysis on a body which has two components which are in dynamic elastic and frictional contact with each other.

04 June 2024 8,493 6 View

I need articles about the difference between the application of kinetic and static friction coefficients in FSW welding, Can introduce the article?

In FSW welding simulation in Abaqus, I need some articles to check the difference between friction application methods (penalty - kinetic friction and static friction).

24 May 2024 5,006 1 View

Where to find Johnson-Cook parameters for pure Zinc?

I am currently simulating the impact of a zinc interlayer between Aluminum workpieces in ABAQUS (Friction stir welding process). While it was easy to find in literature the Johnson-Cook...

21 May 2024 1,643 0 View

What is the correct formula for maximum friction stress value TAUMAX in ANSYS APDL?

Dear all, I'm interested in the analysis of the contact between two deformable bodies using the ANSYS APDL. However, i couldn't reach correct results for the tangential contact problem exactly...

13 May 2024 6,780 1 View

Can you recommend an equation to predict the maximum slide thickness in function of the propagation distance, slope angle and slide properties?

We would like to predict the maximum slide thickness at a particular location along a laboratory slope from an initially triangular-shaped dry granular slide released as a dam break. Can you...

13 May 2024 6,316 0 View

Does the Moon revolve around the Earth friction and hat is the force that causes the moon to revolve around the Earth?

02 May 2024 5,685 3 View

What unit is U/s in anton paar rheometer?

Hello everyone, I'm trying to obtain curves of friction coefficient as a function of entrainment speed using a tribology setup geometry in an Anton Paar rheometer. However, the software gives me...

01 May 2024 4,089 2 View

How can I get the coefficient of static friction - kinetic friction and temperature coefficient for alloy Ag31?

For thermal analysis of FSW magnesium alloy welding by SPH method in Abaqus software, I need static friction coefficients - kinetic friction and Decay coefficient. Can someone help me how to get...

22 April 2024 3,944 1 View

How can I obtain friction velocity(u∗) and scaling humidity (q∗) values in order to calculate transfer coefficient for latent heat(Cez)?

I want to calculate the latent heat flux(Qe) and for that I need the Cez value.

03 April 2024 6,844 3 View