22 January 2024 1 364 Report

The coating electrolles of NiP have properties absorbing and speculary at the same time.

More Gedvidas Bikulcius's questions See All
What aluminum alloys are used in piston production?

Interesting and of piston production methods.

27 May 2024 1,112 3 View

At what is the lowest temperature possible with a synthetic NiS (NiS2) compouds?

Hi everyone, I am especially interested in chemical and electrochemical methods. Thanks.

02 March 2024 8,396 0 View

What aluminium oxide pores will absorber more light?

Let us compared Al oxide pores perpendicular to the Al substrate and parallel to each other with patirs not parallel to each other, i. e. irregularly deviated from perpendicular to the substrate....

03 January 2024 3,109 3 View

Is there a relationship between the adhesion of paint-steel obtained by scratch mesh and single scrath methods?

Hello everyone, Adhesion measurements were performed after paint-steel exposure in the NSS (neutral salt spray) chamber. P. S. On of the scratches in the paint coating was done before...

27 September 2023 7,064 0 View

Is have a correlation between the reflection of blackbody and its band-gap?

I am especially intetested inanodized and blackened aluminium and its alloys.

04 September 2023 6,382 2 View

How cold the mechanical properties of flies from divers be measured?

Hello, It is important to choose the best fly divers (source of chitin) at least qualitatively. Thanks Gedvidas

28 March 2023 3,023 1 View

How is the average coefficient of friction calculated?

Hello, It is interesting, how the average coefficient of friction iš calculated and what its physical meaning is. Sincerely, Gedvidas Bikulcius

28 February 2023 3,041 0 View

Hello everyone, Maybe someone knows how to blacken aluminium only by anodizing it?

In addition the laight reflection of the oxide layer must not exceed 5 percent. Sincerely, Gedvidas Bikulcius

23 February 2023 8,754 2 View

What methods are used to stop the rate of dissolution of magnesium (its alloy) in physiological solution?

Hello colleagues, It is known that rapid dissolution of orthopedic implants is dangerous. What methods are used to stop the rate of dissolution of magnesium (its alloy) in physiological...

29 September 2020 2,094 5 View

Similar questions and discussions
Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

Why can't we get on top of this incubator infection (fungal)?

We have been experiencing repeated what looks very much like fungal contaminations in several incubators (in the same lab). We have tried the following repeated times and yet the coating on all...

02 July 2024 6,375 2 View

How to load Remedesivir drug into mesoporous nanoparticles?

Hello, I want to load Remedesivir (RNA polymerase inhibitor) into mesoporous nanoparticles (MSNs). The issue is drug is temperature and pH sensitive and it degrades quickly. I need advice on its...

01 July 2024 889 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close