03 March 2024 0 8K Report

Hi everyone,

I am especially interested in chemical and electrochemical methods.

Thanks.

More Gedvidas Bikulcius's questions See All
What aluminum alloys are used in piston production?

Interesting and of piston production methods.

27 May 2024 1,112 3 View

Where it can be used of NiP black and shiny at the same time?

The coating electrolles of NiP have properties absorbing and speculary at the same time.

21 January 2024 353 1 View

What aluminium oxide pores will absorber more light?

Let us compared Al oxide pores perpendicular to the Al substrate and parallel to each other with patirs not parallel to each other, i. e. irregularly deviated from perpendicular to the substrate....

03 January 2024 3,109 3 View

Is there a relationship between the adhesion of paint-steel obtained by scratch mesh and single scrath methods?

Hello everyone, Adhesion measurements were performed after paint-steel exposure in the NSS (neutral salt spray) chamber. P. S. On of the scratches in the paint coating was done before...

27 September 2023 7,064 0 View

Is have a correlation between the reflection of blackbody and its band-gap?

I am especially intetested inanodized and blackened aluminium and its alloys.

04 September 2023 6,382 2 View

How cold the mechanical properties of flies from divers be measured?

Hello, It is important to choose the best fly divers (source of chitin) at least qualitatively. Thanks Gedvidas

28 March 2023 3,023 1 View

How is the average coefficient of friction calculated?

Hello, It is interesting, how the average coefficient of friction iš calculated and what its physical meaning is. Sincerely, Gedvidas Bikulcius

28 February 2023 3,041 0 View

Hello everyone, Maybe someone knows how to blacken aluminium only by anodizing it?

In addition the laight reflection of the oxide layer must not exceed 5 percent. Sincerely, Gedvidas Bikulcius

23 February 2023 8,754 2 View

What methods are used to stop the rate of dissolution of magnesium (its alloy) in physiological solution?

Hello colleagues, It is known that rapid dissolution of orthopedic implants is dangerous. What methods are used to stop the rate of dissolution of magnesium (its alloy) in physiological...

29 September 2020 2,094 5 View

Similar questions and discussions
What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What are possible strategies can be used to analyze data under sequential explanatory mixed method approach?

Better ways to analyze the qualitative and quantitative data in a sequential explanatory mixed method approaches

04 August 2024 2,703 6 View

Why 3 replicates for most biological assays? Is it enough to examine the data fits normal distribution?

Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...

31 July 2024 8,141 13 View

Request for Advice: Starch Metabolism Research Project?

I am currently considering a research project focusing on a comparative analysis of starch metabolism in orchids and roses. I am particularly interested in identifying the types and quantities of...

30 July 2024 4,267 2 View

How to calculate conductivity using Electrochemical Impedance Spectroscopy's Nyquist plot?

Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...

29 July 2024 1,376 0 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Pragmatic inquiry research design?

Employing a pragmatic inquiry research design, looking for published research using this method, employing qualitative research data collection methods of semi-structured interview and focus...

28 July 2024 540 2 View

Can i apply a public questionnaire but analyse it with a different data analysis method?

First, thanks for taking the time to read my puzzle 🥹! I am currently working on the methodology part of my dissertation, and I have chosen a questionnaire as the instrument for my quantitative...

27 July 2024 3,457 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close