How i can design isolated gate driver in Cadence Virtuoso?

Ozan Güney Düşmezer @Ozan-Gueney-Duesmezer

22 June 2020 0 6K Report

I want to design isolated gate driver in Virtuoso. How can i make isolation? Also i need bjt library models for driving part of driver. Driver will have push pull bjt's and driving signal isolation.

Badges
Science topic

More Ozan Güney Düşmezer's questions See All

CO2 and CO2- difference in fluent database?

Hello, I'am modeling NH3/H2 fuel mixture combustion via EDM. I am using following reactions in the model: NH3+0,75O2=0,5N2+1,5H2O H2+0,5O2=H2O My combustor has two inlets. One is fuel inlet,...

25 December 2023 8,187 0 View

Can a carbon nanotube have diameter of 500 nanometers?

I have been working on producing CNT's using a freshly designed cold walled CVD reactor. as catalyst I use iron nanoparticles. hot surface is graphite and temparature is between 500C and 700C. C...

08 March 2022 2,753 5 View

Identification / characterisation of carbon nanotubes from electron microscope pictures?

Attached I have some pictures of carbon nanotube that I produced with a coldwall CVD tank with ethanol vapour. Vacuum level was 250 pascals (not that low). Hot surface was a graphite plate around...

14 September 2021 2,386 8 View

Appropriate material for resistance heating to reach 700 Celcius degrees?

I need a very hot surface to do CVD experiments for Carbon nanotube production Hot surface is in a vacuum tank I am using a AC Transformer which gives 1,5 Volt and 500Watts. Secondary coil is...

13 May 2021 6,994 11 View

How to increase the water solubility of zinc in phosphate containing zinc fertilizers?

We use zinc salts that dissolve well in water such as zinc sulphate monohydrate in the production of compound fertilizers. Although we lower the pH, the solubility of zinc salt, which has a very...

16 August 2020 5,291 3 View

What is the main difference between the density of a fluid and a static liquid?

In fluid dynamics, Bernoulli's principle states that an increase in the speed of a fluid occurs simultaneously with a decrease in static pressure or a decrease in the fluid's potential energy....

18 May 2020 2,538 26 View

How can I heat ethanol under vacuum up to 700 C degrees without explosion?

I am planning to produce carbon nanotubes using the carbon inside the Ethanol. process is as follows: Inside the Vacuum Chamber, I will be placing 5ml liquid Ethanol. When I vacuum all the air...

16 April 2020 2,632 3 View

What is the relationship between Kondo effect and superconductivity? Does anybody know about the latest work on this issue?

We all know one of the most widely studied phenomena in condensed-matter physics is Kondo effect. Very briefly the milestones are as follows: This field began in 1933 when Wander Johannes de Haas...

19 November 2018 2,023 4 View

Latest Radiotherapy Phantoms

Dear Colleagues; Can you give information (if available) about the latest products of Radiotherapy phantoms which are being produced in last 2 years? .. Regards

10 June 2017 1,571 2 View

What is the best solution for convert the MC output results to Gy ? What is the opinions?

I would like to learn people's opinions about converting the obtained Monte Carlo results into Gray.. Actually there is some methods that i found in literature but let say, there is no sufficient...

17 April 2017 9,017 4 View

How can I simulate an ISFET Array model in Cadence Virtuoso?

I want to simulate an ISFET Array with a read-out circuit in Cadence Virtuoso which can detect electrolyte from a sample solution.

12 June 2024 6,441 0 View

Trying to make optimization for Mixer on different pdk ?

i make a design topology of mixer For my graduation project working at 28 Ghz on cadence with UMC pdk and get this result S(2,1) 3.5db but when trying to make same topology with another pdk on...

09 June 2024 9,729 3 View

How to attach GAAFET library to cadence tool?

I want to know how to attach the Gate all around FET library can be 3nm to cadence tool. Where we can get the 3nm GAAFET Library.

17 April 2024 2,627 0 View

Cadence generic PDK FinFet download?

I have managed to Cadence generic PDK 45nm from the web [1] and found it very good. If somebody could send or link the Generic cadence FinFet PDK "cds_ff_mpt" for studying that'd be great. [1] I...

29 February 2024 5,561 1 View

How to setup testbench in cadence virtuoso for MOSCAP to measure electrical properties like resistors and capacitance ?

I want to extract the electrical properties of MOSCAP in cadence virtuoso but I don't know the exact method how to measure resistance and capacitance and other properties of MOSCAP

05 December 2023 4,667 0 View

How to solve error NW.E.3 in cadence layout simulation?

NW.E.3 : Minimum Nwell enclosure of Stradled NBL>=0.24um

05 November 2023 8,538 0 View

How to calucalate switching activity in cadence virtuoso tool?

The comparison is made at varying data 8 times, 4 times, 2 times, 1 time and 0 time for 8 active high clock pulses for switching activity factor of 100%, 50%, 25%, 12.5% and 0%.

12 October 2023 4,694 2 View

MOSFET is not in saturation reg even when vds> vgs-vth because vgd>vgs-vth. I am working on LNA in cadence. How to decrease the vgd?

My Question is when the VG is directly applied to gate of mosfet, in CS amp, though vds> vgs-vth is satisfied, the fet is not in saturation region because vgd> vgs-vth. How to decrease the vgd to...

20 August 2023 3,306 0 View

How can I use the variable resistance for 55 nm Technology in cadence virtuoso?

I want to draw a circuit for a thermistor.

18 August 2023 6,161 0 View

SRAM read current in cadence simulation?

I am troubling to find that in cadence how read current of single bit cell (6T SRAM ) is measured ? i am doing DC simulation for this but how to make Q / Qbr = 0. Does any one help...

31 July 2023 1,641 1 View