How do I solve this error in ANSYS while modelling an RC Slab subjected to impact?

More Sri Kalyana Rama J's questions See All

What are the contact properties while modeling a RC slab subjected to impact in ABAQUS?

What will be the contact properties for embedding steel reinforcement into concrete, and what will be the contact properties for the impact ball and RC slab while modeling in ABAQUS?

03 April 2015 6,056 1 View

What are the Input parameters for modeling Self Compacting Concrete in ABAQUS?

I have a very basic doubt regarding modeling Self Compacting Concrete in ABAQUS. Are the input paramters the same for Conventional Concrete and Self Compacting Concrete, if not suggest me how to...

01 February 2015 4,575 1 View

How can I get the input parameters for Smeared crack and cohesive zone modeling in ABAQUS?

I was trying to model the behavior of concrete for its possible crack propogation, i was planning to use smeared crack and cohesive zone models in ABAQUS. Do i need the experimental data to input...

01 February 2015 780 2 View

Can someone suggest various numerical models for studying fracture process in concrete?

Can anyone help me in listing out various fracture models for modeling concrete fracture using softwares like ABAQUS. I do also need various numerical models available for studying the fracture...

31 December 2014 458 6 View

Can anybody help me in using Smeared Crack and Cohesive zone modeling of concrete in ABAQUS?

Can anybody help me in using smeared crack and cohesive zone modeling in concrete for different grades. I was actually facing problem in using the same to identify fracture parameters of concrete...

11 December 2014 5,435 1 View

Is there a way to calculate orthotropic properties of RCC for use with ANSYS?

How can I calculate orthotropic properties for RCC in order to use it for composite structures in ANSYS?

07 August 2012 9,297 1 View

3D analysis of a laminated plate using FEM

thanks everybody actually i was a PG student doing my research work on 3D analysis of a laminated plate using FEM in the process got a doubt whether an analysis has to be carried out separately...

31 December 2011 2,358 3 View

is it necessary to go for fracture analysis for calculating stresses in a laminated plate using 3D Finite element analysis

is it necessary to go for fracture for calculating stresses in a laminated plate or is there any other method available for calculating stresses without fracture using 3D Finite element analysis

31 December 2011 4,130 9 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View