How do I calculate amount of condensation in FLUENT ?

17 March 2015 1 1K Report

hello FLUENT user,

please anyone tell me how to calculate amount of condensation in FLUENT?

I have done 3-D simulation (evaporation & boiling ) on FLUENT but i don't known how to calculate net amount of condensation.

Thanks

Sumer Dirbude

Look out in the droplet particle post processing.

Badges
Science topic

More Sudhir Bisen's questions See All

What approved methods exist to convert nanomaterials in powered from into liquid form for use in concrete specimens in the laboratory?

Nanomaterials in a powdered form are challenging to use in laboratory concrete specimen casting. This is due to the minute-sized particles and the safety considerations. Therefore, there is a need...

14 April 2024 5,740 2 View

Sometimes experimental values of concrete parameters are 5 to 10% lower than the values recommended by the international code equations. Why??

For example, the strength parameters of concrete test specimens of any grade of concrete.

14 September 2023 5,049 4 View

Co-staining Calcein and Hoechst 33342; absence of nuclear signal?

Hello all, I encapsulate human mesenchymal stromal cells within polymeric hydrogels, with degradation enabling encapsulated cell spreading. I have long used Calcein AM to stain and confocal image...

24 July 2023 5,118 0 View

Where can we find the protein sequence of a specific Human HLA allele ?

We are trying to look for specific Human HLA allelesa nd their haplotypes. But we atre having a hard time looking for the exact sequence of the haplotype that we need. Could you please let us know...

17 May 2023 1,358 3 View

I added the template but I see no amplification?

This a ligation PCR, which I'm doing it to check if my ligation worked or not. I am using two primer pairs with very similar annealing temperatures. Ideally, if the ligation worked it should...

16 April 2023 3,067 2 View

Can anyone tell me how to calculate the Genetic diversity (Nei) from gel images?

I have done the scoring, but still confused to how to initiate the next step? I have used RAPD and ISSR markers. Please let me know how to do it?

09 March 2023 3,484 3 View

How can we find the gibbs free energy from dsc analysis?

Through dsc we get the enthalpy but how to calculate the gibbs free energy

15 June 2022 3,877 1 View

Explain under which conditions pulse on time is not a significant factor in Electrical discharge machining process?

Current I have done ANOVA analysis. Pulse on time, Pulse current and Gap voltage is input factor and output factor is Material removal rate and Surface roughness. during analysis pulse current is...

24 March 2022 8,972 2 View

I am doing PCR to amplify COX1 using universal primers LCO1490 and HCO2198 in Sitophilus oryzae DNA but I am not getting band?

I have extracted DNA from Sitophilus oryzae adult using DNeasy Blood and Tissue kit. I am doing PCR to amplify COX1 using universal primers LCO1490 and HCO2198 I am not getting band. Sometimes...

11 January 2022 3,055 3 View

What is the difference between review article and overview?

Please share your thought. Your opinion is highly appreciated Regards

30 December 2021 3,046 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Why is there no condensation in my Star-CCM+ fluid film multiphase case?

Hello, I am attempting to get condensation modelling working from a steam/CO2 multi-component gas mixture to a fluid film of water on a cold wall in Star-CCM+. The gas enter the domain above...

12 June 2024 6,095 0 View

Fluid flow through copper tube?

What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?

07 June 2024 9,030 3 View