How do I block an hemisphere in ICEM CFD and get a good quality mesh?

More Nick Juana's questions See All

How does platelet contamination affect the measurement of Lactate Dehydrogenase (LDH) when it comes to lithium-heparinized plasma tubes?

This question is derived from the journal article “The Transition from Gel Separatory Serum to Lithium Heparin Gel Tubes in the Clinical Laboratory,” written by Oguzhan Zengi. The journal...

07 April 2024 1,838 1 View

What is the proper dosage for supplemental biotin in primary cell culture?

I am trying to overexpress a TurboID construct in mouse primary culture cells for validation experiments. Unfortunately the transfection of this construct appears to be killing my cells while...

26 February 2024 8,931 2 View

How to measure the DMA peak of Propolyene?

Hello every expert, When I did the DMA expertment for propolyene, I can't not get the normal spectrum. I intended to find the tg peak of PP, but it was not easy to have the beautiful peak in this...

22 February 2024 7,216 0 View

Repeated measures in three groups: which test to use?

Hello, I have an experiment in which three groups of 15 participants (disorder 1, disorder 2, control group) underwent an exercise test. I have 14 measurement points (each with a 5-min interval)....

13 December 2023 1,508 4 View

After qPCR analysis of gene expression, when is difference in relative fold change actually relevant?

During work for my undergrad thesis, I've examined and compared gene expression of stress-induced genes in plants challenged with a fungal infection. I have calculated the relative fold change and...

22 November 2023 5,518 3 View

Mushroom cultivation: can we reduce water needed for entire process while also providing drinking water for billions of people?

Our social enterprise's focus [0] is mushroom cultivation in developing countries where easy access to water cannot be assumed: 20%, globally, still have to walk away from their premise to get it...

31 October 2023 9,856 0 View

What is the best way to fix cells for non-permeabilized stains?

Hello, I need to stain some primary culture cells in permeabilized and non-permeabilized conditions to test if a protein is localizing to the exterior of the cell membrane. Our existing fixation...

20 September 2023 5,142 3 View

Why did I get a collection of 5 genes when I search for the gene data of SMN1?

This is what I got when I searched for SMN1 (survival of motor neuron 1) gene: https://www.ncbi.nlm.nih.gov/gene/6606 However, when I downloaded the sequence data, I found there are 5 gene...

14 August 2023 8,123 0 View

Where can I find PET microspheres?

I am looking for PET microspheres for a research project that I am conducting for my dissertation.

25 September 2022 1,789 2 View

Physical Explanation of Phased Array Antenna Directivity on Receive?

Phased array antenna directivity is generally explained on transmit. For example, a uniform linear array (ULA) with element spacing of half a wavelength (scanned to boresight) has a directivity...

26 July 2022 6,704 10 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Esmaeel Safijahanshahi

Dear Nick Juana

Here is a pdf file that I think it should be useful.

Nick Juana

Thanks for replying

Your welcome. Was it useful? Do you need more files?

I have found it. I am using ICEM CFD for meshing and CFX for solving so if you have any file on solving it in CFX will be useful. You know about dynamic meshing...?

This file shows how should use the dynamic mesh model. Good luck.

Thank you