How could I get corrosion rate-time relationship from Polarization resistance (PR ) & Tafel tests?

More Qusay A. Al-Kaseasbeh's questions See All

Could you get me this report, please?

Public work research institute of Japan. 1997–2000. Report of cooperative research on limit state seismic design for bridge piers, I-VIII and summary.

03 April 2018 7,248 1 View

Hi Please as you know that neutrophils are the only cells that can express Ly6G. So can I ask which antibody is specific for this marker?

actually, some references mentioned to use Gr-1, however, I think it would be inappropriate to use Gr-1 antibody as it was reported before that it contains antibody for both Ly6C and Ly6G whereas...

02 March 2018 8,474 1 View

The most common types of bacterial contamination that affecting the growth of anadara granosa or Blood Cockles?

Dear all Professors, Researchers, and Colleagues, I need your help by list ''What are the frequent types of bacterial contamination that affecting the growth of anadara granosa or Blood Cockles...

10 November 2017 2,040 0 View

Why assigning the shell section by selecting middle surface, top surface, or bottom surface to represent the reference surface makes difference?

I'm modeling thin-walled columns using shell element in ABAQUS. I'm using different ways to shape the geometry to end up with the same final configuration whatever the way is. I noticed that when...

09 October 2017 1,146 0 View

Do I need to do Symmetry for beam element?

Dear all, I'm trying to reduce the computational time for a model which contains circular shell element and beam element (with pipe profile) in the top ( see the attached pics). Do I need to do...

05 June 2017 8,704 3 View

How to create hard contact between concrete and steel?

I'm modeling Concrete filled steel tube column, but contact properties do not work for me. please check the input file to get more information.

12 March 2017 9,989 11 View

What are the parameters should I input for this UMAT code to get results similar to ABAQUS GUI?

I just wrote the Isotropic Hardening rule Fortran code (attached below), which is similar to what's available in ABAQUS library, if you have experienced with this code before, what are the...

31 December 2016 6,059 3 View

What's the procedure to get the original written data from a figure in published paper?

I'm wondering if there is a way to get the original data for some figures in published research papers? I've tried to contact the authors, but no responses come back, could I get this data from...

11 December 2016 9,837 2 View

Thin-walled column under constant axial and lateral cyclic loading?

Hi, I'm modeling thin-walled column under axial loading and horizontal displacement as shown in attachment 1 using displacement control (Boundary conditions). I decide and input the horizontal...

26 October 2016 3,462 6 View

How can I export or import part, sketches or assemblies from ABAQUS?

I want to use the same geometry that I drew it in ABAQUS and import again in a different ABAQUS model (not copying). I'm trying with File-export to save it, but when I'm gonna import it again, it...

09 October 2016 6,592 4 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

What is the best way to drop a plasmid?

Please address the best way to drop a plasmid. Background: I have a "bait" plasmid resistant to kanamycin and a "prey" plasmid resistant to carbenicillin. After many rounds of streaking on...

25 July 2024 2,532 3 View

What is the right voltage sweep direction for characterization of HER kinetics?

In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...

25 July 2024 7,982 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Feifei bi

Yes, you can perform OCP, potential dynamic polarization and potential static polarization tess.

prof V.S Muralidharan

you can follow polarization resistance changes with time

it is corrosion rate vs time

better follow ZRA

you balance the voltage difference between your weldment and the alloy of equal area with external voltage source like potentio meter with 3V battery cell

The current needed to make the voltage zero is galvanic current

the electrodes should have equal area

you can follow galvanic current with time

Qusay A. Al-Kaseasbeh

Thanks all