What is the best option available for making masonry wall as Blast resistant?

Pertaining to modelling and studying the behavior of the same in ANSYS AUTODYN.

31 December 2014 3,436 6 View

Can anybody provide material related to ANSYS AUTODYN 2D modelling?

I have already referred following link but its not related to 2D...

09 October 2014 4,258 1 View

How to measure ENERGY practically?

09 October 2014 7,271 3 View

Can anybody provide me with good references for the analysis of 2D-RC Frame due to Blast loads?

Can anyone guide me how to approach this problem? I want suggestions for good references if anybody has a good amount of knowledge in this area. I have to numerically simulate RC frame in AUTODYN...

09 October 2014 8,490 4 View

Can anybody suggest me what is the demanding research topic to be carried out for blast response and its simulation?

In context to perform analysis in AUTODYN ANSYS

08 September 2014 9,906 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to calculate BREQ 3 questionnaire?

how to calculate BEHAVIOURAL REGULATION IN EXERCISE QUESTIONNAIRE BREQ 3 ,which contain 24 questions and each question has 5 answers (0- Strongly disagree , 1-disagree, 2- Neither agree nor...

02 March 2021 811 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View

Please suggest a good text book for "Research Methodology in Life Sciences". Which book would be good for PhD Scholars?

Please provide Book Title and author name

02 March 2021 9,059 3 View

Could any one guide me, to write research proposal for grant? ?

We have one plant, the local people using this for controlling blood sugar, the toxicity and antidiabetic activity of the plant is not reported yet, please guide from whag should be the process ?...

02 March 2021 2,300 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View