How can we do Implicit-Explicit analysis in ANSYS autodyn?

For Blast resistant design of masonry wall, I want to apply axial compression to wall panel by Implicit analysis and the carry out Explicit analysis for blast loading. Is it possible in ANSYS...

03 April 2015 1,744 1 View

What is the best option available for making masonry wall as Blast resistant?

Pertaining to modelling and studying the behavior of the same in ANSYS AUTODYN.

31 December 2014 3,436 6 View

Can anybody provide material related to ANSYS AUTODYN 2D modelling?

I have already referred following link but its not related to 2D...

09 October 2014 4,258 1 View

How to measure ENERGY practically?

09 October 2014 7,271 3 View

Can anybody provide me with good references for the analysis of 2D-RC Frame due to Blast loads?

Can anyone guide me how to approach this problem? I want suggestions for good references if anybody has a good amount of knowledge in this area. I have to numerically simulate RC frame in AUTODYN...

09 October 2014 8,490 4 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to access MSCI KLD Stats and Sustainalytics?

Hello all, I'm currently working on my undergraduate thesis and I'm having difficulties trying to access KLD Stats and Sustainalytics because my campus Airlangga University and apparently other...

02 March 2021 8,525 1 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View