How can we do Implicit-Explicit analysis in ANSYS autodyn?

For Blast resistant design of masonry wall, I want to apply axial compression to wall panel by Implicit analysis and the carry out Explicit analysis for blast loading. Is it possible in ANSYS...

03 April 2015 1,744 1 View

What is the best option available for making masonry wall as Blast resistant?

Pertaining to modelling and studying the behavior of the same in ANSYS AUTODYN.

31 December 2014 3,436 6 View

Can anybody provide material related to ANSYS AUTODYN 2D modelling?

I have already referred following link but its not related to 2D...

09 October 2014 4,258 1 View

Can anybody provide me with good references for the analysis of 2D-RC Frame due to Blast loads?

Can anyone guide me how to approach this problem? I want suggestions for good references if anybody has a good amount of knowledge in this area. I have to numerically simulate RC frame in AUTODYN...

09 October 2014 8,490 4 View

Can anybody suggest me what is the demanding research topic to be carried out for blast response and its simulation?

In context to perform analysis in AUTODYN ANSYS

08 September 2014 9,906 4 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View