How can I vary composition of two materials for a structure in comsol?

More Siddartha Haran's questions See All

What are some of the most x-ray transparent metals with high yield strength?

I am trying to build an x-ray in-situ compression device and would like to use an x-ray transparent metal so that in-situ imaging would be possible.

12 April 2023 5,865 3 View

What is the preference between biological incolation and organic fertilization?

Which one is more compensated for the lack of major elements NPK in the soil, is it biological pollination or organic fertilization and how much are those ratios?

22 September 2020 9,532 3 View

How to generate working ligand-protein complex pdb file for further molecular dynamics run?

the atom order in ligand shows mismatch and thus i cannot proceed to next step

31 July 2020 9,075 6 View

How can we design sequential rotation feed network for patch antennas ?

I need to design sequential rotation feed network for patch antenna array . how can i find the width of the particular impedance to match final 50 ohm impedance.

25 June 2019 800 4 View

Can anyone suggest good books for microstrip patch antenna array designing?

I have refereed few books and didn't find much information related to the feeding network design for the patch antenna array designing. so, please suggest best books or papers for array designing.

11 September 2018 7,685 2 View

How to design sequentially rotated feeding networks for patch antenna?

I require information and good literature related to sequentially rotated feeding networks for microstrip patch antenna.

11 September 2018 9,499 0 View

Can anyone suggest good literature for designing microstrip array feeding networks?

i am facing a problem in designing patch antenna feeding networks. so, please provide some good literature for designing feeding networks.

11 September 2018 9,348 1 View

How to design patch antenna array feeding networks?

I need information related to design of feeding networks.

11 September 2018 5,694 6 View

What are the important aspects to be considered in designing an microstrip antenna array?

i am trying to design a microstrip antenna array for large gain in the order of 30 to 40 db.so need some valuable information regarding that.i also need know about the feeding network. Thanks in...

01 February 2018 3,993 3 View

How to use optimization algorithms in HFSS?

I am trying to use optimization techniques...my question is how to use optimization algorithms such as GA,PSO and etc, in HFSS software.... Thanks in advance...

31 October 2017 6,300 4 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Hakeem Niyas

Could you please explain a bit more about your problem

Siddartha Haran

im working on making cantilever in comsol . I need to make cantilever with a compiste material .so in material tab there is a option to add a spefic material to domain but i need a composition of two material ,That too i need to vary the compoistion

Bouraoui Ilahi

I think it's possible to do this task by defining different material having different composition: It's takes a lot of time but can works