How can I use Ansys program in corrosion field?

More Rana Afif Majed Anaee's questions See All

What is the best method to get doped carbon nanotube?

I am working on doping of carbon nanotube and I would like to know what is the best dopant and the easiest method for this?

01 February 2017 1,596 9 View

What is the difference between doping and addition according to the weight percents of additives in EDS analysis?

When we add any material to electrolyte of coating, how can we consider the additive if it is a dopant or only an additive according to the EDS analysis?

31 December 2016 3,168 13 View

Can I use oxalic acid with aniline for electropolymerization?

I would like to apply polyaniline coating in acidic medium, which is the best acid for coating by Potentiostat?

08 September 2016 9,268 2 View

What is the best anion may be improved the polymer coating?

If we would like to add some anions to polymer coating. What are the best as dopant using electrochemical method for coating?

08 September 2016 4,644 2 View

What is the best method to apply polymeric coating?

We would like to apply conductive polymer coating on metallic alloy. What is the best method for this?

06 July 2016 1,992 11 View

Please, can anyone help me to separate nanowires from washing solution?

I fabricated nanowires and after complete dissolving of template, I need to obtain the dried nanowires. Can anyone help me to achieve this process?

04 May 2016 5,089 10 View

Can anyone help me to interpret the following DSC scan for Al-Ti alloy?

I have DSC for Al-Ti alloy and its composites with MgO and SiC and there are shifting in peaks to upper or lower regions, Please can any one help me to interpret them?

02 March 2016 9,264 4 View

Can I measure some properties of nano wire deposited in AAO template?

I deposited nanowire by electrochemical method using AAO template and I would like to measure some properties of it. Can I achieve the measurement without dissolve the template?

02 March 2016 8,004 4 View

Can any one tell me about a journal is publishes quickly?

I have a paper about corrosion and I need to publish quickly.

01 February 2016 4,800 2 View

What are the most important tests to characterize nanowires?

I fabricate nanowire and I would like to characterize it?

01 February 2016 7,453 4 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How to solve g_mmpbsa error?

Program: g_mmpbsa, version 2024.1 Source file: extrn_apbs.cxx (line 152) Fatal error: Failed to execute command: $APBS pybYcUWA.in --output-file=pybYcUW.out

07 August 2024 6,066 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Are students in the MBA program in Fisheries Enterprises Management eligible to work in the aquaculture industry abroad?

Are students in the MBA program in Fisheries Enterprises Management eligible to work in the aquaculture industry abroad? Could you explain the foreign countries interested in recruiting...

28 July 2024 8,378 2 View

How can we calculate the percentage of configuration interaction (CI) in the UV output data of the Gaussian program?

How can we calculate the percentage of configuration interaction (CI) in the UV output data of the Gaussian program? for example: Excited State 17: Singlet-A 5.1359 eV 241.41 nm...

28 July 2024 9,165 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View