What is the best anion may be improved the polymer coating?

More Rana Afif Majed Anaee's questions See All

What is the best method to get doped carbon nanotube?

I am working on doping of carbon nanotube and I would like to know what is the best dopant and the easiest method for this?

01 February 2017 1,596 9 View

What is the difference between doping and addition according to the weight percents of additives in EDS analysis?

When we add any material to electrolyte of coating, how can we consider the additive if it is a dopant or only an additive according to the EDS analysis?

31 December 2016 3,168 13 View

Can I use oxalic acid with aniline for electropolymerization?

I would like to apply polyaniline coating in acidic medium, which is the best acid for coating by Potentiostat?

08 September 2016 9,268 2 View

What is the best method to apply polymeric coating?

We would like to apply conductive polymer coating on metallic alloy. What is the best method for this?

06 July 2016 1,992 11 View

Please, can anyone help me to separate nanowires from washing solution?

I fabricated nanowires and after complete dissolving of template, I need to obtain the dried nanowires. Can anyone help me to achieve this process?

04 May 2016 5,089 10 View

Can anyone help me to interpret the following DSC scan for Al-Ti alloy?

I have DSC for Al-Ti alloy and its composites with MgO and SiC and there are shifting in peaks to upper or lower regions, Please can any one help me to interpret them?

02 March 2016 9,264 4 View

Can I measure some properties of nano wire deposited in AAO template?

I deposited nanowire by electrochemical method using AAO template and I would like to measure some properties of it. Can I achieve the measurement without dissolve the template?

02 March 2016 8,004 4 View

Can any one tell me about a journal is publishes quickly?

I have a paper about corrosion and I need to publish quickly.

01 February 2016 4,800 2 View

What are the most important tests to characterize nanowires?

I fabricate nanowire and I would like to characterize it?

01 February 2016 7,453 4 View

What is the best method to analyze the chemical composition of metal matrix composite? XRD analysis didn't give any change compared with base alloy.

Please can any one help me? I fabricated four aluminum matrix composite with SiC and MgO, and I need the best method to find the exact chemical composition after casting. What is the best method...

01 February 2016 1,081 14 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What are possible strategies can be used to analyze data under sequential explanatory mixed method approach?

Better ways to analyze the qualitative and quantitative data in a sequential explanatory mixed method approaches

04 August 2024 2,703 6 View

What is the ionic radius of Hydrogen anion? And how to know the exact ionic radii of the elements?

I'm trying to calculate the tolerance factors of the hydride perovskite and the value calculated by me and the reported values are contradictory. Need more clarity in using the correct ionic radii...

01 August 2024 2,614 1 View

Why 3 replicates for most biological assays? Is it enough to examine the data fits normal distribution?

Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...

31 July 2024 8,141 13 View

Request for Advice: Starch Metabolism Research Project?

I am currently considering a research project focusing on a comparative analysis of starch metabolism in orchids and roses. I am particularly interested in identifying the types and quantities of...

30 July 2024 4,267 2 View