How can i uniform the thickness on curved surfaces during the Dip molding process?

More Jaewoo Shin's questions See All

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

SDS page software for analysis?

I did sds page to determine the difference in protein expression between 3 types of vaccine , but i don't have scanner or densitometer available. . so i wonder if there is a software to analyze...

02 March 2021 6,270 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Does any one can help me choose a reasonable basis set for intermediate metal ions interactions with guanine (i.e Fe2+, Mn2+, Cu2+ and exc.)?

Hello every body Does any one has any idea to help me choose a reasonable basis set for intermediate metal ions (i.e Fe2+, Mn2+, Cu2+ and exc.) interactions with guanine or other DNA organic...

01 March 2021 6,187 2 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

What could be some reasons why unstimulated monocytes are getting activated?

Im doing PBMC isolation -> CD14+ enrichment using magnetic beads -> stimulation setup. My negative control is just cells in cRPMI but they seem to get activated over and over again.

28 February 2021 7,883 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

Rana Hadi Al-Shammari

Optimize Dipping Parameters: Adjusting the withdrawal speed and angle during the dipping process can help to achieve uniform thickness on curved surfaces. It is important to carefully control the withdrawal speed to ensure that the coating material adheres evenly to the curved surface.

Jaewoo Shin

Rana Hadi Al-Shammari Thank you so much for your reply