Does anyone know about modelling tensile contact behavior in abaqus?

I modeled 2 part in abaqus and i want to until tensile stress between 2 surface is T, it transmit between 2 surface and up to T, to surface be separate of each other. Is there any model in...

04 May 2015 9,382 1 View

How do you request a .fil output in abaqus?

I need a .fil output in abaqus . I typed *node file in input file in abaqus to have a .fil. but when I import input file this warning appears. WARNING: The following keywords/parameters are not...

02 March 2015 3,677 3 View

Is it necessary to use of 3D8R element in damage plasticity model in abaqus?

I want to use of damage plasticity model in abaqus. when i use of 3D8R elements, the running complete easily, but when i use of 3D20R, abaqus cant solve the model. Is it necessary to use of 3D8R...

02 March 2015 6,004 4 View

How can I prevent this problem in converging in explicit analysis in abaqus?

I have a 2D model in abaqus (Explicit) and analysis is quasi-static (with time 50). Material model is damage plasticity. I can see some crack in my model. But when I refine mesh, displacement will...

31 December 2014 6,489 3 View

How to define slide contact between two edge in abaqus explicit in a quasi-static analysis?

I modeled a 2D model in abaqus explicit. My analysis is quasi-static. When I put a hard contact between two edge, a divergence occur in my result. I can understand why this problem occurs. Time in...

31 December 2014 9,862 2 View

I have used of tie constrain in abaqus between two surfaces but after analyzing, two nodes are separate, why?

31 December 2014 7,345 4 View

Error in abaqus: "Stiffnesses of spring element 5 instance is too high..."how can I solve this problem without reducing my stiffness?

I modeled a cantilever in with many springs in downstream of it to model arch effect. but stiffness of my spring is too large and abaqus make an error. how can i solve this problem without reduce...

11 December 2014 3,045 1 View

How can I apply the trial load method to my 2D model?

I have a 2D model in abaqus and I want to apply the arch effect on my model by a function of pressure on downstream surface. How is the the function of arch effect? linear of another function?

11 December 2014 1,145 1 View

Can abaquse model the staged construction?

I want to model a Dam in 8 stage.

10 November 2014 9,390 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View